564780
4
Zoom out
Zoom in
Previous page
1/4
Next page
4
Entries
Basic Sales Entry
Listed below is a basic sales entry example when selling items by cash. For details, refer to “FULL DETAILED
INSTRUCTUION MANUAL”.
1.
Enter the clerk code and press the key.
2.
Enter the unit price and press the appropriate department
key.
3.
Repeat step 2 for all department items.
4.
When the item entry is completed, press the key.
The total amount due is displayed.
5.
Receive the amount from your customer, and enter the
amount by the numeric keys.
6.
Press the key. The change due is displayed, and the
drawer is opened.
7.
Close the drawer.
Department Entries
Enter a unit price and press a department key.
If you use a programmed unit price, press a department key
only.
Department keyUnit price
(max. 8 digits)
When using a programmed unit price
PLU (Price Look Up) Entries
PLU code entry (max. 5 digits)
Enter a PLU code using the numeric keys, and press the key.
For example, enter “71” and press the key for “PLU 00071”.
For ER-A421, press the key instead of the key.
PLU code or
Direct PLU entry (ER-A421 only)
Enter a unit price and press a direct PLU key.
If you use a programmed unit price, press a direct PLU key
only.
Direct PLU keyUnit price
(max. 8 digits)
When using a programmed unit price
EAN Entries
Create EAN8/13-Codes in REG mode
This is the easiest way to register and to store EAN Codes before you open your shop or to work for the rst
time with the cash register.
After an EAN code scanning, you may be requested to enter a unit price with the display “UNDEFINED CODE”
and beep sound. Set the unit price, department code, and delete type.
Unit price Dept. code
“UNDEFINED CODE” display
and beep sounds
Dept. code input window
is displayed.
Delete method selection
window is displayed.
*Selection of
delete method
Scan an undefined
EAN code
* Select “2 NO DELETE” to store the article continuously.
At the next scan entry of this EAN code, the registration is automatically done without the above steps.
EAN code entry (8 or 13 digits)
Enter the EAN code using the numeric keys, and press the key.
For ER-A421, press the
key instead of the key.
EAN code scanning (8 or 13 digits)
Read the EAN code on the item with the scanner.
Scan EAN code
EAN code
or
Correction
Correction of entered number ( )
When you enter an incorrect number, delete it by pressing the key immediately after the entry.
Correction of the last entry ( )
If you make a mistake when making a department entry, PLU entry, percentage ( ) and discount ( ), you
can correct this entry by pressing the
key immediately.
Correction of earlier entries (
)
You can correct any incorrect entry made during a transaction if you nd it before nalizing the transaction by
pressing the
key. Move the cursor to the item to be voided and press the key.
Subtotal void (
)
You can void an entire transaction. Once subtotal void is executed, the transaction is aborted and the register
issues a receipt.
Press the key immediately after pressing the key. And then press the key again.
Correction after nalizing a transaction (VOID mode)
When you need to void incorrect entries that are found after nalizing a transaction or cannot be corrected by
direct, indirect or subtotal void, the following steps should be taken.
1.
Enter to the manager mode by following the steps on the
right.
D
The key is not included in the standard keyboard for ER-A421.
To use the VOID mode, consult your authorized SHARP dealer.
Manager
code
or
Secret
code
2.
Press the
key to put your register in the VOID mode.
3.
Repeat the entries that are recorded on an incorrect
receipt.
5
Reading and Resetting Sales
Overview
Use the reading function (X) when you need to take the reading of sales information entered after the last
resetting. You can take this reading any number of times. It does not affect the register’s memory.
Use the resetting function (Z) when you need to clear the register’s memory. Resetting prints all sales
information and clears the entire memory except for the GT1 through GT3, reset count, and consecutive
number.
X1 and Z1 reports show daily sales information. You can take these reports in the X1/Z1 mode.
X2 and Z2 reports show periodic (monthly) consolidation information. You can take these reports in the X2/Z2
mode.
In the OP X/Z mode, a clerk can take his or her report.
This register supports various types of reports including general report, department report, PLU/EAN report,
and clerk report. For details on available reports, refer to “FULL DETAILED INSTRUCTION MANUAL”.
If you want to stop the printing report, press the
C
key.
D
When both sales quantities and sales amounts are zero, printing is skipped. If you do not want to skip,
change the programming. For details, refer to “FULL DETAILED INSTRUCTION MANUAL”.
“X” represents read symbol and “Z” represents reset symbol in the reports.
When printing is performed continuously, the printing may be intermitted for several seconds. After the
intermission, the printing will be restarted.
How to Take a Report
1.
Press the key.
2.
Select the appropriate mode from the following by using the key, and press the key.
1 OPXZ MODE
3 X1/Z1 MODE
4 X2/Z2 MODE
3.
Select the operation from the following by using the key, and press the key to display the items list.
1 READING
2 RESETTING
4.
Select the appropriate report title.
5.
Press the key.
Flash Report
You can take ash reports (display only) in the X1 mode for department sales, cash in drawer (CID) and sales
total at the point you take the report.
1.
Press the key.
2.
Select the “3 X1/Z1 MODE” by using the key, and press the key.
3.
Select “3 FLASH MODE”, and press the key.
4.
Select the appropriate report title from the following by using the key.
1 DEPT. SALES Department sales
2 CID Cash in drawer
3 SALES TOTAL Sales total
5.
Press the key.
D
When you select “1 DEPT. SALES” in step 4, select the appropriate department from the departments list.
Replacing the Paper Rolls
The register can print receipts and journals. For the printer, you must install the paper rolls (receipt and journal
paper rolls) provided with the register.
Be sure to set a paper roll prior to using your machine, otherwise it may cause a malfunction.
Be careful then to set the roll correctly.
(How to set the paper roll)
To the printer
Incorrect
To the printer
Correct
Recording paper speci cations
Be sure to use paper rolls speci ed by SHARP.
The use of any other paper rolls than speci ed could cause paper jamming, resulting in register malfunction.
Paper speci cation
Paper width: 57.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality: High quality (0.06 to 0.08 mm thickness)
Paper tube: 18 mm
Removing the paper rolls
When a red dye appears on the paper roll, it is time to replace the existing paper roll. Replace the paper roll
with a new one. If you plan not to use your register for an extended period of time, remove the paper roll, and
store it in the appropriate place.
Print roller arm
Print roller
release lever
1.
Remove the printer cover.
<Receipt side>
2.
Lift up the print roller release lever to unlock the print roller arm. The arm
will come up slightly.
Open the print roller arm of the receipt side.
3.
Remove the paper roll from the paper roll cradle of the receipt side.
Cut
Take-up
spool
<Journal side>
4.
Press the key to advance the journal paper until its printed part is out
of the way.
5.
Cut the paper and remove the take-up spool from the bearing.
Print roller arm
6.
Lift up the print roller arm of the journal side.
7.
Remove the paper roll from the paper roll cradle of the journal side.
8.
Remove the paper holding plate of the take-up spool, and remove the
printed journal roll from the spool.
Installing the paper rolls
<Receipt side>
1.
Remove the printer cover and open the print roller arm of the receipt side
by following the steps in “Removing the paper rolls”.
2.
Set a paper roll in the paper roll cradle of the receipt side as per the
diagram.
3.
Feed the end of the paper along with the paper positioning guides as per
the diagram.
4.
While holding down the paper, slowly close the print roller arm of the
receipt side, and push down the
mark on the arm until you hear a
click locking the arm.
D
If the print roller arm is not securely locked, printing is not done right. If this
problem occurs, open the arm, and close the arm as instructed above.
5.
Wait until the excess paper is automatically cut off, and remove it.
D
Do not remove the excess paper until the receipt cutter stops completely.
Trying to remove the paper before the cutter stops completely could cause
paper jamming.
<Journal side>
6.
Lift up the print roller arm of the journal side.
7.
Set a paper roll in the paper roll cradle of the journal side as per the
diagram.
Paper positioning guides
8.
While holding down the paper, slowly close the print roller arm of the
journal side, and push down the arm until you hear a click locking the
arm.
Spool
Paper holding plate
9.
Remove the paper holding plate from the spool.
Insert the end of the paper into the slit in the spool. (Press the journal
paper feed key to feed more paper if required.)
Wind the paper two or three turns around the spool shaft.
Speci cations
Model:
ER-A411/ER-A421
Dimensions:
360(W) × 425(D) × 365(H)* mm
* With the customer display popped up. When it is
completely lowered, the height is 330 mm.
Weight:
Approx.12.0kg
Power source:
Of cial (nominal) voltage and frequency
Power consumption:
Standby: 7.1W (220 to 230V, 50Hz/60Hz)
7.3W (230 to 240V, 50Hz)
Operating: 31.6W (220 to 230V, 50Hz/60Hz)
28.1W (230 to 240V, 50Hz)
Working temperatures:
0 to 40 ºC
Display:
Operator display: LCD display with tilt mechanism
192(W) × 80(H) dots
Customer display: 2-line LCD display
Printer:
Type:
Two-station thermal printer
Printing speed:
Approx. 15 lines/second
Printing capacity:
30 digits each for receipt/journal paper
Other functions:
Receipt ON/OFF function
Compression print for an electronic journal/journal
Receipt and journal independent paper feed
function
Logo:
Graphic logo printing:
Size: 130(H) x 360(W)pixel
Area of black must be less than 35% of all area.
Logo message printing:
Logo message for the receipt
(max. 30 characters x 6 lines)
Paper Roll:
Width: 57.5±0.5 mm
Max. diam.: 80 mm
Quality: High quality (0.06 to 0.08 mm thickness)
Cash drawer:
5 slots for bills and 8 for coin denominations
Accessories:
Basic User Manual: 1 copy
Paper roll: 2 rolls
Take-up spool: 1
Paper holding plate: 1
Drawer lock key: 2
Standard key sheet: 1 (for ER-A421 only)
Programming key sheet: 1 (for ER-A421 only)
Fixing angle bracket: 1
The display does not illuminate.
Is power supplied to the electric outlet?
Is the power cord plug out or loosely connected to the
electric outlet?
Is the register in screen-save mode?
The display is illuminated, but the whole machine
refuses entries.
Is a cashier code assigned to the register?
Is a clerk code assigned to the register?
Is the register in the REG mode?
No receipt is issued.
Is the receipt paper roll properly installed?
Is there a paper jam?
Is the receipt function in the “OFF” status?
Is the print roller arm securely locked?
No journal paper is taken up.
Is the take-up spool installed on the bearing properly?
Is there a paper jam?
Printing is unusual.
Are the printer head/sensor/roller clean?
Is the paper roll properly installed?
Before Calling for Service
If you encounter any of the following problems, please read below before calling for service.
4000
Item entries
Clerk assignment
Displaying subtotal
Amount tendered
Finalizing the transaction
Key operation example
*
: indicate department keys.
1
1500
*
2300
*
SHARP ELECTRONICS (Europe) Ltd.
4 Furzeground Way, Stockley Park Uxbridge,
UB11 1 EZ, United Kingdom
6
Operator Maintenance
In Case of Power Failure
When power is lost, the register retains its memory contents and all information on sales entries.
When power failure is encountered in register idle state or during an entry, the register returns to the normal
state of operation after power recovery.
When power failure is encountered during a printing cycle, the register carries out the correct printing
procedure after power recovery.
In Case of Printer Error
If the printer runs out of paper, the printer will stall, and “PAPER EMPTY” will appear on the display. Key entries
will not be accepted. Referring to “Replacing the Paper Rolls” in this chapter, install a new paper roll in the
proper position, then press the key. The printer will print the power failure symbol and resume printing.
If the print roller arm comes up, the printer stalls, and “HEAD UP” will appear on the display. Key entries will
not be accepted. Push down the arm until it is securely locked, then press the
key. The printer will print the
power failure symbol and resume printing.
Cautions in Handling the Printer and Recording Paper
Cautions in handling the printer
Avoid the following environments:
Dusty and humid places
Direct sunlight
Iron powder (A permanent magnet and electromagnet are used in this machine.)
Never pull the paper when the print roller arm is locked. First lift up the arm, and then remove the paper.
Never touch the surface of the print head and print roller.
Cautions in handling the recording paper (thermal paper)
Use only the paper speci ed by SHARP.
Do not unpack the thermal paper until you are ready to use it.
Avoid heat. The paper will color at around 70°C.
Avoid dusty and humid places for storage. Avoid direct sunlight.
The printed text on the paper can discolor under the following conditions:
Exposure to high humidity and temperature
Exposure to the direct sunlight
Contact with glue, thinner or a freshly copied blueprint.
Heat caused by friction from scratching or other such means.
Contact with a rubber eraser or adhesive tape.
Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed
text with a photocopier.
10.
Mount the paper holding plate onto the take-up spool.
Set the spool on the bearing, and press the journal paper feed key to
take up excess slack in the paper.
11.
Replace the printer cover.
12.
Press the key to make sure the paper end comes out of the printer
cover and clean paper appears.
D
If the paper end does not come out, open the printer cover, and pass the
paper end between the paper cutter and the paper guide of the printer
cover, and replace the printer cover.
Removing a paper jam
1.
Remove the printer cover.
2.
Lift up the print roller arm.
3.
Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.
4.
Reset the paper roll correctly by following the steps in “Installing the paper rolls”.
Drawer Handling
Locking the Drawer
Develop the habit of locking the drawer when not using the register for any
extended period of time.
TL-1
To lock: Insert the key into the drawer lock and turn it
90 degrees counter-clockwise.
To unlock: Insert the key into the drawer lock and turn it
90 degrees clockwise.
Removing the Drawer
Drawer
Till
Coin case
To remove the drawer, pull it out and lift it up.
D
To prevent burglary, it is a good idea to empty the drawer after work and
leave it open at the end of the day.
Coin case is detachable.
Manually Opening the Drawer
Lever
In case of a power failure or if the machine is out of order, locate the lever
at the bottom of the machine and move it in the direction of the arrow to
open the drawer. The drawer will not open if it is locked with the drawer
lock key.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp ER-A421 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp ER-A421 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp ER-A421

Sharp ER-A421 User Manual - English - 226 pages

Sharp ER-A421 Quick start guide - German - 4 pages

Sharp ER-A421 User Manual - German - 226 pages

Sharp ER-A421 Quick start guide - Dutch - 4 pages

Sharp ER-A421 User Manual - Dutch - 226 pages

Sharp ER-A421 User Manual - French - 226 pages

Sharp ER-A421 User Manual - French - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info