17535
16
Zoom out
Zoom in
Previous page
1/84
Next page
14
MAKING COPIES
NORMAL COPYING
This copier has two document input stations –– a reversing
single pass feeder (RSPF) for automatic document feeding
and an original table for manual handling of bound
documents. The RSPF is designed to hold up to 30 originals
measuring from 5-1/2" x 8-1/2" to 11" x 17" and in the
weight range of 15 to 24 lbs.
Be sure to remove any staples or paper clips from the
originals.
Damaged or crumpled originals may misfeed in the RSPF.
It is recommended that these originals be copied from the
original table.
Before placing curled or wavy originals into the document
feeder tray, be sure to flatten them. If not, original misfeeds
may result.
For best feeding of originals which have binding holes
punched into them, insert them so that the holes are
positioned to the right or along the side guides. In this case
the settings for location of margin and image rotation in
duplex copying may need to be changed to ensure the
images are produced in the desired orientation. See pages
22 and 41.
Special originals such as transparency film and tracing
paper should not be fed through the RSPF but should be
copied from the original table.
The bypass tray and any tray with non-standard size paper
cannot be used in the duplex copy mode.
Paper sizes that can be used in the duplex mode are 8-1/2"
x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17".
If the offset stack mode is enabled using user program No.
19, each set of copies will be offset from the previous set
in the sort and group modes.
Stream feeding mode
If the stream feeding mode has been enabled using user program No. 4, the RSPF indicator
will continue to blink for approximately 5 seconds after feeding of all originals is completed.
While this indicator is blinking, any new originals placed in the RSPF will be fed and copied
automatically. See page 51, USER PROGRAMS.
Power on
Power on
1
Turn the power switch on.
It will take about 35 seconds for the copier to warm up.
However, you can make desired settings and press the START key
during warm-up. Copying will start after warm-up.
If the copier has been programmed in the auditing mode, the START
key indicator will not light up and “ ” will appear in the copy
quantity display. Enter an assigned 3-digit account number. See page
13.
If an optional printer expansion kit or facsimile expansion kit is
installed, when the power is already on and all indicators except the
POWER SAVE indicator are off, the copier is in the auto power shut-
off mode. Press the START key in this case. See page 58, POWER
SAVE MODES.
One-sided copies from one-sided originals
1
Ensure that no original is left on the original table.
2
Adjust the original guides to the size of the originals.
3
Set the originals face up in the document feeder tray.
The RSPF indicator will light up. If this indicator does not light up, the
originals are not properly set, or the RSPF is not properly closed.
Normal copying
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp AR207 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp AR207 in the language / languages: English as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info