668672
5
Zoom out
Zoom in
Previous page
1/6
Next page
PRECAUTIONARY MEASURES
OPERATING INSTRUCTIONS
Important: If the suction opening of the hose is BLOCKED, switch off the vacuum
cleaner and remove the blocking substance before you start the unit
again.
Fig. 11
6. Vigorously “TapClean”
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (fig. 11)
Fig. 12
Debris
Screen
7. “TapClean” the Debris
Screen or rinse under
a faucet until clean.
(fig. 12) Remember
that the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
8. Replace the Debris Screen on the
HEPA Dust Cup Filter and reinstall
filter assembly in the vacuum. (not
shown)
CAUTION: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) This should be
done once a month or when
suction appears reduced.
Fig. A
Wash once a
month or when
suction
appears
reduced.
.
Warning: Allow 24
hours for drying before
replacing in unit.
Cleaning & Changing the
HEPA Dust Cup Filter cont.
IMPORTANT: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
Push the On/Off button once.
Disconnect the plug from the
power source.
Check the source of overheating
problem. (i.e. clogged hose or
filter)
If clogged hose or filter is found,
unclog the hose and replace the
filters.
Wait at least 45 minutes before
attempting to reuse the vacuum.
After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
If the vacuum still does not start,
contact customer service at
1-800-798-7398.
Motor Thermostat
4. When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
1. Do not operate the vacuum
cleaner too close to heaters or
radiators.
2. Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
3. Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the HEPA Filter.
5. Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
6. Do not use without HEPA filter in
place.
7. Do not bend, trample or pull the
hose by force. Do not operate with a
damaged hose.
8. When vacuuming fine dust particles
such as gyproc dust, flour or any
other fine dust, empty the dust cup
and "TAPCLEAN
TM
" the dust cup
filter frequently to avoid over heating
the motor.
6 3
5


Need help? Post your question in this forum.

Forumrules
1

Forum

shark-v1510

Reset search

  • How do I buy a new crevice tool for this hand held vacuum? Submitted on 19-6-2021 at 22:50

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark V1510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark V1510 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Shark V1510

Shark V1510 Additional guide - English - 2 pages

Shark V1510 Additional guide - English - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info