668611

Shark NV356K Manual

15
Zoom out
Zoom in
Previous page
1/20
Next page
TOLL FREE: 1-800-798-7398
15www.sharkclean.com
Fig. 25
Fig. 24
Fig. 26
CLEANING THE POST-MOTOR HEPA FILTER
1 Remove the filter cover from the front of the
vacuum by pulling up on the tab and pulling the
cover away from the vacuum. (Fig. 24)
2 STake out the HEPA filter by pulling it straight out.
3 Turn the filter over so that the dirty side is on
the bottom and vigorously tap it clean against a
garbage can to remove any dust. (Fig. 25)
4 Wash the filter under the tap using lukewarm
water with the dirty side face down until the water
runs clear. (Fig. 26)
DO NOT put the filter in the washing machine or
dishwasher.
NOTE: The material in the filter will discolor over
time. This is NORMAL and will not affect the
performance of the filter.
5 Allow the filter to air dry for 24 hours. Do not use
a hair dryer or other heating methods to dry.
6 Once the HEPA filter is dry, replace it back into the
vacuum.
7 Replace the cover by inserting the two tabs into
the holes at the top and then swinging the cover
down until it clicks into place.
Fig. 30
Fig. 29
a
CLEANING THE POWER BRUSH (model NV356E,
NV356K, NV357 only)
1 Slide the locking latch (a) forward and gently tilt
brush housing upward to open. (Fig. 29)
IMPORTANT: DO NOT force; it will not open all
the way.
2 Carefully remove any blockage or debris.
3 Turn the power brush over to inspect the rotating
brush and cut away any build-up of hair or string
wrapped around the rotating bristle brush with
scissors. (Fig. 30)
4 Push the housing back down and slide the locking
latch backward to lock.
CLEANING THE POWER BRUSH
(model NV355 only)
1 Slide the locking latch (a) forward and tilt the
bottom cover upward to remove. (Fig. 27)
2 Carefully remove any blockage or debris and
cut away any build-up of hair or string wrapped
around the rotating bristle brush with scissors.
3 To reassemble, insert the tabs on the front edge
of the bottom cover into the matching holes in the
top half and tilt it back down until it clicks into
place. (Fig. 28)
Fig. 28
Fig. 27
a
Maintenance - cont’d
NV355_NV356E_NV356K_NV357_IB_110714_3.indd 15 11-07-20 9:32 AM
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark NV356K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark NV356K in the language / languages: English as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info