576369
16
Zoom out
Zoom in
Previous page
1/20
Next page
12
TOLL FREE: 1-800-798-7398
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Vac-OR-Steam
will not
turn on.
Your Vac-OR-Steam
should be securely plugged into a 120V AC electrical
outlet only.
Check your fuse or breaker.
Check to make sure the steam or vacuum nozzle is attached correctly.
The Vac-OR-Steam
will not
make steam.
Make sure the water tank is filled to the indicated fill line.
Attach Steam Pad and Steam Nozzle to base of the unit.
TILT MOP HANDLE BACK TO GENERATE STEAM.
The Vac-OR-Steam
leaves
water on the floor.
Check to see if your multi-purpose cleaning pad has absorbed too much
moisture. We recommend you unplug the Vac-OR-Steam
and replace the
multi-purpose cleaning pad.
Make sure the steam pad is attached correctly.
Wait 30 seconds after choosing the steam setting before mopping, allowing
water to heat to a 212°F sanitizing steam. If the unit is not allowed to heat
properly, some water may be emitted.
The Vac-OR-Steam
is hard to push.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the pad is too
dirty or wet.
The Vac-OR-Steam
is not picking up dirt.
Check filters to see if they need cleaning. Follow instructions for rinsing and
drying the filters before re-inserting back into the unit. (See “Maintenance”
sections for instructions.)
Dust cup may be full. Empty the dust cup.
Check nozzle or the air intake hose for blockages. Clear blockages if required.
Check that no debris has clogged the brushroll on the vacuum nozzle. Follow
instructions in “Cleaning the Vacuum Nozzle” section to clean the brushroll.
The Vac-OR-Steam
turns off
on its own.
The Vac-OR-Steam
is equipped with a motor protective thermostat. If for
some reason your appliance overheats, the thermostat will automatically turn
the unit off. Should this occur, perform the following steps to restart the motor
thermostat:
1.
Step on the foot pedal until it goes to standby mode.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters. (See “Maintenance” sections for
instructions.)
4.
Check for blockages in hose, accessories and inlet openings. (See
“Checking for Blockages” for instructions.)
5.
Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Step on the foot pedal to select the vacuum mode and tilt the vacuum
back to start vacuuming.
MV3010_40_ENG_IB_120713_2.indd 12 12-07-13 1:36 PM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark MV3010 Rotator Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark MV3010 Rotator Professional in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info