668636
5
Zoom out
Zoom in
Previous page
1/11
Next page
4
TOLL FREE: 1-800-798-7398
5
www.SharkVacThenSteam.com
English
3 Place your foot lightly on the top
of the cleaning unit base. Tilt the
cleaning unit back. Vacuum your
floors.
IMPORTANT: Vacuum all surfaces
first before steam-cleaning to
avoid condensation build-up. Avoid
vacuuming after steam mopping.
NOTE: If you vacuum and then
steam-clean one room, before
moving on to the next, wait 10
minutes for the condensation to
clear before vacuuming again.
USING VACUUM MODE
1 Pull and twist the quick release cord
holder to unwrap the power cord
completely. Plug in the unit.
2 To vacuum, slide the toggle switch
until the vacuum power button is
exposed. Press the vacuum power
mode button to the ON I” position.
IMPORTANT: You cannot use the
vacuum function if the frame and
pad are attached to the base of the
cleaning unit.
NOTE: Only vacuum sealed and
non-carpeted bare floor surfaces.
Refer to floor manufacturer
guidelines and warnings.
Getting Started: Vacuum and Steam Panel Vacuum Mode
OPERATING IN VACUUM MODE:
1 Remove steam pad and frame,
if attached. See page 11 for
instructions. Vacuum will not activate
if steam frame is attached.
2 SLIDE THE TOGGLE SWITCH UP to
expose the vacuum power button.
3 Press the VACUUM POWER BUTTON
to the ONI” position to activate
the vacuum.
OPERATING IN STEAM MODE:
1 Attach steam pad and frame.
Steam mode will not work if the pad
and frame are NOT attached. See
page 8 for assembly instructions.
2 Fill the water tank.
SLIDE THE TOGGLE SWITCH DOWN
to expose the Steam Power button.
3 Press the STEAM POWER BUTTON
to the ONI position. The button
will be illuminated red when steam
mode is activated.
4 Wait 30 seconds to heat water, then
TILT HANDLE BACK TO ACTIVATE
STEAM PUMP.
The Vac-Then-Steam™ has two
operating modes:
After inserting the telescopic handle,
your cleaning system is vacuum-ready.
Begin vacuuming your hard-surface
floors by tilting the cleaning unit back
and pressing the vacuum power button.
2
3
1
1
1
2
2
3
3
VACUUM MODE:
STEAM MODE:
DO NOT USE STEAM PAD AND
FRAME IN VACUUM MODE
MV2010WC_11_IB_ENG_100803.indd 4-5 04/08/10 9:38 AM
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark MV2010WC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark MV2010WC in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info