743742

Shark ION Robot RV860WVC Series Manual

11
Zoom out
Zoom in
Previous page
1/33
Next page
OWNER’S GUIDE
GUIDE D’UTILISATION
RV860WVC
Series • Série
ROBOT & HANDHELD
ROBOT ET ASPIRATEUR PORTATIF
ION
TM/MC
sharkclean.comsharkclean.com
QUICK
START
GUIDE
GENERAL WARNINGS
1. Robotic vacuum cleaner consists of a
robotic vacuum and charging dock with
power supply. These components contain
electrical connections, electrical wiring,
and moving parts that potentially present
risk to the user.
2. Before each use, carefully inspect all
parts for any damage. If a part is damaged,
discontinue use.
3. Use only identical replacement parts.
4. This robotic vacuum cleaner contains no
serviceable parts.
5. Use only as described in this manual.
DO NOT use the robotic vacuum cleaner
for any purpose other than those
described in this manual.
6. With the exception of filters, DO NOT
expose any parts of the robotic vacuum
cleaner to water or other liquids.
USE WARNINGS
7. This appliance is not intended for use
by anyone (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety. Children should be
supervised to ensure that they do not
play with the appliance.
8. Always turn o the robotic vacuum
cleaner before inserting or removing the
filter or dust bin.
9. DO NOT handle plug, charging dock or
robotic vacuum cleaner with wet hands.
10. DO NOT use without dust bin and filters
in place.
11. Only use Shark® branded filters and
accessories. Failure to do so will void
the warranty.
12. DO NOT damage the charging cord:
a) DO NOT pull or carry charging dock
by the cord or use the cord as a
handle.
b) DO NOT unplug by pulling on cord.
Grasp the plug, not the cord.
c) DO NOT close a door on the cord,
pull the cord around sharp corners, or
leave the cord near heated surfaces.
13. DO NOT put any objects into nozzle or
accessory openings. DO NOT use with
any opening blocked; keep free of dust,
lint, hair, and anything that may reduce
airflow.
14. DO NOT use if robotic vacuum cleaner
airflow is restricted. If the air paths
become blocked, turn the vacuum
cleaner o and remove all obstructions
before turn on the unit again.
15. Keep nozzle and all vacuum openings
away from hair, face, fingers, uncovered
feet, or loose clothing.
16. DO NOT use if robotic vacuum cleaner
is not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
17. DO NOT place vacuum cleaner on
unstable surfaces.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
IMPORTANT SAFETY INSTRUCTIONS: ROBOT
PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
18. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects (glass, nails,
screws, or coins)
d) Large quantities of dust (drywall dust,
fireplace ash, or embers). DO NOT use
as an attachment to power tools for
dust collection.
e) Smoking or burning objects (hot
coals, cigarette butts, or matches)
f) Flammable or combustible materials
(lighter fluid, gasoline, or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
19. DO NOT use in the following areas:
a) Wet or damp surfaces
b) Outdoor areas
c) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
20. Turn o the robotic vacuum cleaner
before any adjustment, cleaning,
maintenance or troubleshooting.
21. Allow all filters to air-dry completely
before replacing in the robotic vacuum
cleaner to prevent liquid from being
drawn into electric parts.
22. DO NOT modify or attempt to repair the
robotic vacuum cleaner or the battery
yourself, except as indicated in this
manual. DO NOT use the vacuum if it has
been modified or damaged.
BATTERY USE
23. The battery is the power source for the
vacuum. Carefully read and follow all
charging instructions.
24. To prevent unintentional starting, ensure
the vacuum is powered o before
picking up or carrying the vacuum.
DO NOT carry the appliance with your
finger on the power switch.
25. Use ONLY the Shark® charging dock
RVDOK850WV and battery RVBAT850.
Use of batteries or battery chargers
other than those indicated may create a
risk of fire.
26. Keep the battery away from all metal
objects such as paper clips, coins, keys,
nails, or screws. Shorting the battery
terminals together increases the risk of
fire or burns.
27. Under abusive conditions, liquids may be
ejected from the battery. Avoid contact
with this liquid, as it may cause irritation
or burns. If contact occurs, flush with
water. If liquid contacts eyes, seek
medical help.
28. Robotic vacuum cleaner should not be
stored, charged, or used at temperatures
below 50°F (10°C) or above 104°F
(40°C). Ensure that the battery and
vacuum have reached room temperature
before charging or use. Exposing the
battery to temperatures outside of this
range may damage the battery and
increase the risk of fire.
29. DO NOT expose the robotic vacuum
cleaner or battery to fire or temperatures
above 265°F (130°C) as it may cause
explosion.
If the charging cable plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
ENGLISH
For additional warnings, go to sharkclean.com/robothelp
sharkclean.comsharkclean.com
QUICK
START
GUIDE
POWER SUPPLY, CHARGING DOCK,
AND VACUUM CONTAIN ELECTRICAL
CONNECTIONS:
• There are NO serviceable parts.
• DO NOT use to vacuum any liquids.
• DO NOT immerse in water or other liquids.
• If vacuum is damaged, discontinue use.
• To avoid fire, explosion, or injury, inspect
vacuum and charging dock for any damage
before use.
• DO NOT use damaged vacuum or charging
dock.
• DO NOT use outdoors or on wet surfaces.
Use only on dry surfaces.
• If vacuum cleaner is not working as it
should, or has been dropped, damaged, left
outdoors, or immersed in water, return it to
SharkNinja Operating LLC for examination,
repair, or adjustment.
• DO NOT handle charger or vacuum cleaner
with wet hands.
• DO NOT leave vacuum cleaner unattended
while powered on.
• Keep vacuum away from heated surfaces.
• Always turn o vacuum before connecting
charging dock.
• Use only Shark® chargers and batteries.
Other types of batteries may burst, causing
injury and damage.
• Use charging dock on flat and stable
surfaces only.
• DO NOT incinerate appliance, even if it is
severely damaged, as lithium-ion battery
may explode in a fire.
GENERAL USE
• DO NOT carry the charger by the cord or
yank to disconnect from an outlet; instead
grasp the plug and pull
to disconnect.
• Keep charger cord away from heated
surfaces.
• Use only as described in this manual.
• Keep your work area well lit.
• To avoid unintentional starting, always turn
o the vacuum cleaner before picking it
up or carrying it, and before attaching or
detaching the charger, dust cup, filter, or
any accessories.
• DO NOT put any objects into openings.
• DO NOT use if any opening is blocked; keep
free of dust, lint, hair, or anything that may
reduce airflow.
• DO NOT allow young children to operate
the appliance or use as a toy. Close
supervision is necessary when any
appliance is used near children.
• DO NOT use without dust cup and filter in
place.
• DO NOT use if airflow is restricted; if the air
paths become blocked, turn o the vacuum
cleaner. Clear all obstructions and power
on again.
• Keep nozzle away from hair, face, fingers,
uncovered feet, or loose clothing.
• Only use manufacturer’s recommended
attachments.
• DO NOT charge at temperatures below
50°F (10°C) or above 104°F (40°C).
Charging improperly or at temperatures
outside of the specified range may damage
the battery and increase the risk of fire.
• Store the appliance indoors. DO NOT use
or store it below 37.4°F (3°C). Ensure the
appliance is at room temperature before
operating.
WARNING
To reduce the risk of injury, fire, electric shock, and property damage resulting from
improper use of the appliance, carefully observe the following instructions. This unit
contains electrical connections and moving parts that potentially present risk to the user.
IMPORTANT SAFETY INSTRUCTIONS: HANDHELD
PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
DUST CUP/FILTERS/ACCESSORIES
Before turning on the vacuum:
• Make sure filter is thoroughly dry after
routine cleaning.
• Make sure dust cup and filter are in place
after routine maintenance.
• Make sure accessories are free of blockages
and keep openings away from face and
body.
• Use only Shark® brand filters and
accessories. Using other brands will void
warranty.
GENERAL CLEANING
• DO NOT vacuum up hard or sharp objects
such as glass, nails, screws, or coins that
could damage the vacuum cleaner.
• DO NOT vacuum up drywall dust, fireplace
ash, or embers.
• DO NOT use as an attachment to power
tools for dust collection.
• DO NOT vacuum up smoking or burning
objects such as hot coals, cigarette butts,
or matches.
• DO NOT vacuum up flammable or
combustible materials (e.g., lighter fluid,
gasoline, or kerosene) or use vacuum in
areas where they may be present.
• DO NOT vacuum up toxic solutions (e.g.,
chlorine bleach, ammonia, or drain cleaner).
• DO NOT use in an enclosed space where
vapors are present from paint, paint
thinner, moth-proofing substances,
flammable dust, or other explosive or toxic
materials.
• DO NOT immerse vacuum cleaner in water
or other liquids.
• Use extra care when cleaning on stairs.
LITHIUM-ION BATTERY
• The battery is the power source for the
appliance. DO NOT carry the appliance
with your finger on the power button. DO
NOT charge appliance with the power on.
• Use only the included charging dock to
charge. Use of incorrect charger may
create a risk of fire.
• Use appliance only with included lithium-ion
battery. Use of any other battery may create
a risk of injury and fire.
• Under abusive conditions, liquid may be
ejected from the battery. Avoid contact
with liquid, as it may cause irritation or
burns. If contact occurs, flush with water. If
liquid contacts eyes, seek medical help.
• Store the appliance indoors. To maintain
battery life, DO NOT use or store battery at
temperatures below 37.4°F (3°C) or above
104°F (40°C).
• DO NOT expose appliance to fire or
temperature above 266°F (130°C) as it may
cause explosion.
• There are NO serviceable parts. To ensure
safety, DO NOT modify or attempt to repair
the appliance.
If the charging cable plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
sharkclean.comsharkclean.com
5 ft.
3 ft.
3 ft.
CHARGING THE SHARK ION
TM
ROBOT CHARGING THE SHARK ION
TM
ROBOT
IMPORTANT: The Shark ION Robot has a pre-installed rechargeable battery. Battery must be fully charged
before using.
Place the Charging Dock on a level surface with its back against a wall, in a space without obstructions, that
can easily be accessed by your robot. Remove any objects that are closer than 3 feet (1 meter) from either
side of the dock, or closer than 5 feet (1.52 meters) from the front of the dock. Plug the Charging Adapter
into a wall outlet. The dock must be plugged in continually for the robot to find it. The robot will beep when
it starts charging on the dock.
The power must be ON in order to charge the battery.
Press the Power button on the side of the robot.
If the robot has no charge and cannot return to the
charging dock, place it on the dock manually.
When the cleaning cycle is complete, or if the battery
is running low, the robot will begin to search for
the dock. If the unit doesn’t return to the dock, the
battery charge may have run out.
The blue Charge Indicator Lights
show how much charge is remaining.
CHARGING DOCK
CHARGINGCHARGE INDICATOR LIGHTS
While the battery is charging, all three blue LED
lights will cycle until charging is complete.
If all the indicator lights are o, then either the
power switch is turned OFF or there is no charge
remaining. Turn the power switch ON. If all
indicator lights remain o, then charge the unit
on the dock.
No Charge Full Charge
Low ChargeMid ChargeNearly FullFull Charge
No Charge Full Charge
Low ChargeMid ChargeNearly FullFull Charge
In Use
While
Charging
sharkclean.comsharkclean.com
Prior to first use, the lithium-ion battery must be
charged completely, even if it comes with
a partial charge.
Place the Shark ION Handheld onto the charging
dock with the air-intake nozzle
in the cradle.
Plug the charging dock into a wall outlet.
Solid blue
In Use
Dim
Charged
Fades in
and out
Charging
Blinking
Low Battery
CHARGING THE SHARK ION™ HANDHELD
CHARGE INDICATOR LIGHTS
NOTE: During first use, discharge fully to properly condition the battery. It takes approximately 2.5 hours to
charge completely.
USING THE SHARK ION™ ROBOT
BUTTONS AND INDICATOR LIGHTS
CLEAN BUTTON
Press to begin a long-running
cleaning session. Press again
to stop.
DOCK BUTTON
Press to stop cleaning and
send robot back to the
charging dock.
MAX MODE BUTTON
Press to begin a
powerful cleaning.
CHARGE INDICATOR LIGHTS
Display the amount of charge
remaining in the battery.
“!” ERROR INDICATOR
See Troubleshooting section
for full list of error codes.
WI-FI INDICATOR
Blue light: connected to
Wi-Fi.
Red light: not connected.
Flashing blue: setup mode.
No light: not set up yet.
CHARGING DOCK
IMPORTANT: The Shark ION Power Handheld has a pre-installed rechargeable battery. Battery must be
fully charged before using.
sharkclean.comsharkclean.com
USING THE SHARK ION™ ROBOT
MANUAL CLEANING MODE
To manually start a cleaning cycle, press the Clean
button on the robot or on the mobile app. To stop
the robot before it finishes cleaning and automatically
returns to the dock, press the button again.
INSTALLING THE SIDE BRUSHES
The 2 included side brushes snap onto the square
pegs on the bottom of the robot. Press brushes
down onto the pegs until they click into place.
IMPORTANT: Before cleaning an entire room for the first time, we recommend that you first test your robot on a small
section of the floor to ensure there is no scratching.
IMPORTANT: Robot uses cli sensors to avoid stairs and other steep drops. Sensors may work less eectively when they
are dirty. For best results, clean sensors regularly.
TIP: To preserve battery life, turn o the power switch if robot will not be used for a long period of time.
TIP: To preserve battery life, unit should be recharged at least once every three months.
USING THE SHARK ION™ ROBOT
USING THE SHARK ION ROBOT APP AND VOICE CONTROLS
DOWNLOADING THE SHARK ION ROBOT APP
Follow the steps below or scan the QR code to go directly to the download page.
SETTING UP VOICE CONTROL WITH THE GOOGLE ASSISTANT OR AMAZON ALEXA
Visit sharkclean.com/app for setup instructions.
VOICE CONTROL COMMANDS FOR THE GOOGLE ASSISTANT OR AMAZON ALEXA:
The Shark ION Robot app will guide you through easy setup of your Shark ION Robot.
Control the unit remotely:
• Schedule cleaning times for up to 7 days a week.
• Start, stop, or dock your Shark ION Robot from your phone anywhere with Wi-Fi connectivity.
The app will also provide you access to:
• Tips, Tricks, and FAQs
• Tech Support
• Troubleshooting
Android:
• Tap on the Google Play Store icon
• In the Play Store, search for
“Shark ION Robot”
• Tap on the Shark ION Robot app
• Tap install on the Shark ION Robot app page
• Your installation should begin
OR
Type the address below into your
web browser: bit.ly/shark-droid
Google Assistant:
“OK Google, tell Shark to start cleaning.”
“OK Google, tell Shark to pause my robot.”
“ OK Google, tell Shark to send my robot to
the dock.”
Apple:
• Tap on the App Store icon
• Search the Apple App Store for
“Shark ION Robot”
• Tap on the Shark ION Robot app
• Tap Install on the next page
• Your installation should begin
OR
Type the address below into your
web browser: bit.ly/shark-ios
Amazon Alexa:
“Alexa, tell Shark to start cleaning.”
“Alexa, tell Shark to pause my robot.”
“ Alexa, tell Shark to send my robot to
the dock.”
sharkclean.comsharkclean.com
USING THE SHARK ION™ ROBOT
PAIRING THE ROBOT WITH A SMART PHONE
To ensure you successfully pair with the robot:
• Confirm your Wi-Fi router and/or home network supports a 2.4 GHz network.
• Confirm your Wi-Fi network name.
• Confirm your Wi-Fi network password.
• Reboot your home router.
• Confirm you have downloaded the latest version of the Shark ION Robot app on
App Store or Google Play Store.
USING THE SHARK ION™ ROBOT
PAIRING THE ROBOT WITH A SMART PHONE
Read and agree to the
Terms of Use.
Watch the video tutorial on
setting up and using the app.
Launch the app. Make sure the robot is on.
Press and hold the Dock and
Max buttons at the same
time for 5 seconds, or until
the robot beeps. The Wi-Fi
Indicator light will begin to
blink on your robot.
If you have an account,
tap Sign In. To create an
account, enter a valid
e-mail address and create
a password. A confirmation
code will be sent to the
e-mail address provided.
Make sure your phone is
connected to the same 2.4
GHz Wi-Fi network that your
robot will be connected to.
Enter confirmation code.
1
2
3
4
5
6
8
7
Register your robot.
You are now ready to
schedule cleaning days and
times for your robot.
Your phone will automatically
connect to your robot.
You will be notified when
your robot is connected.
Give your robot a name,
then tap Continue button.
Connect your phone to the
robot's Wi-Fi Network. The
network's name will start with
SHARK_RV-.
1
2
3
4
5
For more information, see sharkclean.com/app
sharkclean.comsharkclean.com
USING THE SHARK ION™ ROBOT
5 ft.
3 ft.
3 ft.
CORDS AND OBSTRUCTIONS
DOORWAY THRESHOLDS
LOW-CLEARANCE FURNITURE
RETURNING TO DOCK
Smart Sensor Technology
Robot Traps Robot Friendly
Smart Sensor Technology allows your robot to navigate around obstructions as it cleans.
During your first few cleanings, you may need to make some small adjustments to optimize
your robot’s performance.
Before cleaning, clear away cords and other
obstructions or block o the area with the included
BotBoundary™ strips.
Your robot may have some trouble clearing some
high thresholds. Block o high thresholds with
BotBoundary strips.
To prevent your robot from becoming trapped,
use furniture risers or BotBoundary strips.
Make sure the dock is set up as shown. If your
robot roams too far, it could have trouble finding
the dock. It may be helpful to block o part of your
home with the included BotBoundary strips, or to
add a second dock (available at sharkaccessories.com)
USING THE SHARK ION™ ROBOT
!
!
BotBoundary strips
BotBoundary strips
Cut the BotBoundary strip to the desired length
(18˝/45cm minimum) so that it spans the length of
the doorway or object you want to block o.
Identify areas or objects you want the vacuum to avoid.
To keep Shark ION Robot away from certain areas, such as pet bowls, fragile objects, power
strips, or doorways, use the BotBoundary strips to quickly and easily create “no-go zones”.
NOTE: To prevent bumping, place strips at least 2 inches in front of the object you want to block o.
NOTE: You do not need to use BotBoundary strips on stairs. Your robot has cli sensors that will prevent it from falling
o any ledges or stairs.
BotBoundary™ strips
For best results, make sure your BotBoundary strip
is completely flat against the floor. Make a closed
loop around an object, or place the strips between
fixed objects, like door frames or the legs of a couch
to create no-go zones.
!
4-inch
Min.
For your robot’s cli sensors to work properly,
all runners, rugs, or carpets must be at least
4 inches from any stairs (or extend over the edge
of the stairs.)
If a runner, rug, or carpet edge is less than
4 inches from the stairs and can’t be moved,
use a BotBoundary strip to block o the stairs.
sharkclean.com sharkclean.com
USING THE SHARK ION™ HANDHELD
MAINTENANCE: ROBOT
EMPTYING THE DUST BIN
Press the dust bin removal button and slide out the
dust bin at a slight downward angle.
CAUTION: Turn o power before performing any maintenance.
Press and hold the button down with one hand
while inserting fingers into slots and pulling the
lid open.
Empty debris and dust into trash.
1 2
3
EMPTY DUST BIN AFTER EACH USE.
Press Power button.
1 2
3 4
Run the nozzle over the surface to
be cleaned.
Hold your ION Power Handheld over
the trash.
Slide dust cup button forward to
release debris.
sharkclean.comsharkclean.com
CLEANING THE FILTER
MAINTENANCE: ROBOT
Remove and empty the dust bin. Clean any hair or
debris o the Anti-Tangle Comb on the back of
the dust bin.
Pull filter out of the dust bin by the tabs.
Lightly tap the filter to remove dust and debris.
Rinse filter with water only, and let air-dry 24 hours
before reinstalling.
Reinsert the filter into the dust bin. Slide the dust
bin back into the robot.
CLEAN FILTER EVERY WEEK.
REPLACE FILTER EVERY TWO MONTHS. See sharkaccessories.com for replacement filters.
CLEANING THE BRUSHROLL
MAINTENANCE: ROBOT
Push up on the tabs on the brushroll access door,
then lift o the door.
Lift out the brushroll. Remove the cap on the end
of the brushroll. Clean o any hair or debris, then
replace cap.
Clean the brushroll periodically and whenever hair
appears.
Reinstall the brushroll, inserting the flat end first.
Close the brushroll access door and press down
until it clicks into place.
NOTE: When removing the brushroll cap, make sure to not let the bushing inside the cap fall out. When cleaning
brushroll, be sure to not cut anything other than hair, string, fibers, or other debris.
CLEAN BRUSHROLL EVERY WEEK.
REPLACE BRUSHROLL EVERY 6 to 12 MONTHS, OR WHEN VISIBLY WORN. See sharkaccessories.com for replacement
parts.
sharkclean.comsharkclean.com
CLEANING SENSORS AND CHARGING PADS
CLEANING SIDE BRUSHES
MAINTENANCE: ROBOT
Carefully unwind and remove any string or hair
wrapped around brushes.
Gently wipe brushes with a damp cloth. Be sure to
let them air-dry completely before reinstalling them.
CLEAN SENSORS AND CHARGING PADS PERIODICALLY AS NEEDED. Gently dust o the sensors and pads located on the
bottom of the unit with a dry cloth or cleaning brush.
NOTE: Remove any side brushes that are bent or damaged. To remove a brush, lift it o its post. See "Installing the Side
Brushes" for instructions on how to attach and remove the brushes.
CLEANING THE FRONT CASTER WHEEL
REPLACING THE BATTERY
MAINTENANCE: ROBOT
Pull the caster wheel from its housing and remove
any debris buildup.
To remove the battery, turn the unit over and
unscrew the battery cover with a Phillips-head
screwdriver.
Unplug the old battery from its connector, then
plug in the new battery. Replace battery cover and
screw it back into place. See Battery Recycling
information on back of cover.
REMOVE AND CLEAN FRONT WHEEL EVERY WEEK. REPLACE FRONT WHEEL EVERY 12 MONTHS.
See sharkaccessories.com for replacement parts.
Clean the wheel housing, then reinsert the
caster wheel.
CLEAN SIDE BRUSHES AS NEEDED. CHECK WEEKLY.
RECOMMENDED REPLACEMENT SCHEDULE: Replace when visibly worn. See sharkaccessories.com for replacement parts.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark ION Robot RV860WVC Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark ION Robot RV860WVC Series in the language / languages: English, French as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info