Manual Shark AI Robot VacMop RV2000WD (page 6 of 39) (English, French, Spanish)

743714

Zoom out

Zoom in

1/39

sharkclean.comsharkclean.com

PREP YOUR HOME

USING THE SHARK® AI ROBOT VACMOP™

IQ NAVIGATION™ AND AI LASER VISION

After setup is complete, follow instructions in the

app to help your robot conduct an Explore Run to

create an initial map of your home.

The robot will travel from room to room to identify

walls, furniture, and other obstacles as it cleans.

This run will take less time than a full cleaning, as it

doesn’t cover the entire ﬂoor.

MANUAL CLEANING MODE

To manually start a cleaning cycle, press the Clean button on the robot or on the mobile app. To

immediately send the robot back to the dock, press the Dock button.

IMPORTANT: Before cleaning an entire room for the ﬁrst time, we recommend that you ﬁrst test your robot on a small

section of the ﬂoor to ensure there is no scratching.

NOTE: Scheduling is one of numerous features that can only be done in the app.

Your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it

cleans. To prevent the robot from entering areas you don't want it to, set up no-go zones in the app. For

best results, prepare your home as indicated below, and schedule a daily cleaning to ensure all ﬂoor areas

are regularly maintained.

NOTE: Be sure to charge the robot completely before

its ﬁrst cleaning so that it can explore, map, and clean

as much of your home as possible. It may take up to 6

hours to fully charge your robot.

NOTE: Avoid moving the dock. If it is relocated, the

robot may not be able to ﬁnd its way back to the dock.

If the robot is relocated while in use, it may not be able

to follow its intelligent cleaning path, or ﬁnd its way

back to the dock.

OBSTRUCTIONS

Clear cords and small objects

less than 2.8" in height, and

open interior doors to ensure

a complete map of your

home.

SCHEDULING

Schedule whole-home

cleanings with the app. To

schedule a mopping run with

the app, the reservoir must

be ﬁlled and installed in the

robot with the pad attached.

THRESHOLDS

Your robot can climb over

most thresholds to get from

room to room, but if one is

too high, set up a no-go zone

in the app to block it o.

AVOID MOVING THE

ROBOT & DOCK

While your robot is cleaning,

do not pick it up and move it,

or move the charging dock—

this will impact the robot’s

navigation and ability to

return to dock when cleaning

is complete.

REMOVE RUGS FROM

DOORWAYS WHEN

MOPPING

Before mopping, you must

set up Carpet Detection in

the app, and move any car-

pets or rugs that block access

to ﬂoors that you want your

robot to mop.

STAIRS

Your robot’s cli sensors will

prevent it from falling o

ledges. For the cli sensors

to work properly in any

mode, all runners, rugs, or

carpets must be at least 16

inches from any stairs, or

must extend over the edge of

the stairs.

The robot's object detection technology helps it

navigate around obstacles taller than 2.8" in height.

Clear away small objects that may interfere with the

cleaning path of your robot.

Create no-go zones in the app to block o areas you

do not want the robot to enter. You can set up no-go

zones around small objects, or use them to block o

large areas.

VACUUM ONLY INSTRUCTIONS

To vacuum, the ﬂuid reservoir must NOT be

attached to the robot. Make sure the dust bin is

properly installed.

Since every room in my house has baseboards, how/where am I supposed to set up the dock? Submitted on 7-1-2022 at 15:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Shark AI Robot VacMop RV2000WD in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 11,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Shark AI Robot VacMop RV2000WD Manual

Product: