663255

Shada 800509 Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
LED’s
light
A
BRAND
SHADA
LED’s
light
A
BRAND
SHADA
WEEE NL: 3505
WEEE DE: 37281017
WEEE AT: 40133
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
LED‘s light
Installatie en gebruiksaanwijzing
Art Nr.
Power
Ingangsvoltage
Lichtstroom
Kleurtemperatuur
Sensor
Branduren (u)
Afmetingen
Algemene veiligheidsinstructies
Lees de gebruiksaanwijzing van de LED plafonnière voor ge-
bruik. De gebruiksaanwijzing is onderdeel van het product. Ze
bevatten belangrijke aanwijzingen voor het opstarten en het
hanteren van het apparaat. Bewaar de bijgevoegde gebruiksa-
anwijzing zorgvuldig voor het raadplegen van informatie. Het
moet worden bijgevoegd bij het passeren van het apparaat
aan derden.
Veiligheidsmaatregelen
De gebruiker moet de veiligheidsinstructies en waarschuwin-
gen in acht nemen om een veilige werking te garanderen. Lees
de handleiding voor gebruik.
Vermijd contact met hoge temperaturen of trillingen. Dit kan
dit schade aan de LED plafonnière veroorzaken. Dompel de be-
huizing LED plafonnière niet onder water.
Probeer nooit het apparaat anders te openen dan beschreven
in deze handleiding. De LED plafonnière kan niet worden her-
steld, bij defect zal het product moeten worden verwijderd.
Zorg voor voldoende ventilatie van het apparaat. Bedek het
nooit tijdens gebruik. Niet geschikt voor gebruik in het bereik
van kinderen of dieren.
Elk ander gebruik van het apparaat dan hierboven beschreven,
kan het product beschadigen of in gevaar brengen van de ge-
bruiker te wijten aan bijv. kortsluiting, brand of een elektrische
schok. Het gehele product mag niet worden gewijzigd of aan-
gepast. Raak LED plafonnière niet aan terwijl hij in gebruik is
of na gebruik totdat het is afgekoeld. De LED plafonnière moet
bij installatie geaard worden aangesloten voor een veilige wer-
king.
Deze veiligheidsvoorschriften moeten in alle gevallen worden
nageleefd. Elke aanspraak op garantie vervalt in geval van
schade veroorzaakt door het niet naleven van deze technische
handleiding. Wij zijn niet aansprakelijk voor gevolgschade of
voor schade aan eigendommen of personen veroorzaakt door
het niet naleven van de veiligheidsvoorschriften en het onjuist
gebruik van het apparaat.
Veilige werking niet meer mogelijk indien:
- De LED plafonnière zichtbare beschadigingen heeft,
- De LED plafonnière niet meer werkt.
Installatieinstructies: →
Aanwijzingen voor verwijdering
Oude eenheden, aangeduid met het symbool zoals
afgebeeld, mag niet weggegooid worden met het
gewone huisvuil.
Je moet ze bij een inzamelpunt deponeren voor
oude eenheden (informeer bij uw gemeente) of de
leverancier van wie u het product kocht. Deze zorgen voor een
milieuvriendelijke verwerking.
Garantie
Voordat u het apparaat schoonmaakt, ontkoppelt u deze van
andere componenten; geen agressieve reinigingsmiddelen te
gebruiken.
Het apparaat is zorgvuldig gecontroleerd op gebreken. Als u
desondanks toch reden tot klagen, ga dan terug naar de winkel
samen met uw aankoopbewijs. Wij bieden een 2 jaar garantie
vanaf de aankoopdatum. Wij zijn niet aansprakelijk voor scha-
de als gevolg van onjuiste behandeling, onjuist gebruik of slij-
tage van het product. Wij behouden ons het recht technische
wijzigingen aan te brengen.
Bezoek ons online op www.shada.nl voor meer informatie over
onze producten en ons bedrijf.
CE declaration
Dit product voldoet aan de volgende richtlijnen:
LVD: 2014/35/EU,
EMC: 2014/30/EU
ROHS: 2011/65/EU
R&TTE Regelgeving: R&TTE 1999/5/EC
800509
18W
230V AC
1.050
3.000K
Yes
25.000
Ø340 x 95mm
Optional: Sensor instellingen (alleen voor art: 800509)
DIP switch: Aan = 1 / Uit = 0
tijd Instelling:
Schemerschakelaar:
Detectibereik overview (diameter)
Detectiebereikinstelling (Gevoeligheid)
Installatiehoogte
Tijdinstelling
Brandduur na detectie
Schemerschakelaar
hoe lager Lux is ingesteld, hoe donkerder het moet zijn voor
de lamp inschakelt.
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
sendeleistung:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Erfassungsbereich
2.5-3.5m
Min:2m
Max:10m
Installationshöhe 2.5~3.5M
Min:2m
Max:10m
(Installationshöhe 2.5M)
Erfassungsbereich
Hinweis !
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wenn sich im Erfassungsbereich des Sensors der
Leuchte Metall befindet, ist die Funktion nicht oder
nur eingeschränkt möglich!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
Zeit:S1,S2
S1
1
1
S2
Zeit
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX
:
S3,S4
S3 S4
TIME:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. Yo u can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
TROUBLESHOOTING
Malfunction Cause
Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
check zone setting
the sensor not mounted for detecting
movement reliably
securely mount enclosure
The load work without any
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
The load will not work despite
movement
rapid movements are being suppressed
to minimize malfunctioning or the
detection zone you have set is too small
Check zone setting
wrong light-control setting selected
Remedy
-2--1-
Microwave Sensor Microwave Sensor
YG-01 instruction YG-01 instruction
SPECIFICATIONS
UTILIZING FIELD AND INTRODUCTION
Zendvermogen:<0.2mW
HF system 5.8GHz CW electric wave,ISM band:
Detection angle 360°:
Light-control:24H/10LUX/50LUX/100LUX(adjustable)
Working temperature: -15~ +60
Power consumption approx.0.5W:
: indoors, ceiling mounting
Installation sit
Time setting:
/ (adjustable)12min±1min
10sec±3sec 3min±10sec/ /6min±30sec
Power source: 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1000W/5A,Max,incandescent lamp(cos
φ=
1)
300W/2.5A,Max,fluorescent lamp and LED lamp(cos
φ=
0.5)
NOTE:
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
th
The high-frequency output of this sensor is
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and turn
off the light automatically when you leave off. You can set the closing delay time to meet your needs. For
example, you may adjust the TIME sliding controller to select the delay time 10sec~30min when you think
you will come back in 30mins. The TIME sliding controller is as follow (Keep away from the detecting zone
after adjusting the testing time or that the detecting time will be inaccurate when any moving object is
detected again by the product).
SENSOR INFORMATION
360
Detectiebereik
2.5-3.5m
Min:2m
Max:10m
Installatiehoogte 2.5~3.5M
Min:2m
Max:10m
(Installatiehoogte 2.5M)
Detectiebereik
Waarschuwing!
Non-metal material
when the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
Wanneer er zich tussen sensor en te scannen
oppervlak metalen delen bevinden, kan dit de
werking beperken of verhinderen!
pr o d u c tThe is a moving object sensor that can detect range of 360°and it’s working frequency is
5.8GHz.The advantage of this product is stable working state (stable working temperature:
-15°C~+70°C), SK605B adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe
and performs better than infrared sensor.
It can be installed inside of product which is made of glass and plastic because microwave
can go through them effect to microwave. Connect the product as below: you can change a
common light into an automatic light.
TIME SETTING
The light can be set to stay ON for any period of time between approx.10sec and a maximum of 12min. Any
movement detected before this time elapse will re-start the timer. It is recommended to select the shortest
time for adjusting the detection zone and for performing the walk test.
Pull switch to the ON position as "1", pull switch to the OFF position as "0”, switch location and detection
range of the corresponding table is as follows:
PARAMETER SETTING
Shown as chart below：By setting S1,S2 to set the delay time of products, by setting the S3, S4 to set the
light-control of products.
S1 S2
TIJD:S1,S2
S1
1
1
S2
TIJD
6min
12min
0
1
0
10s
0
0
3min
1
NOTE: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period
has elapsed.
LIGHT-CONTROL SETTING
The chosen light response threshold can be infinitely from approx. 10-100lux, pull switch to the ON
position as "1" , pull switch to the OFF position as "0”, switch location and light-control of the
corresponding table is as follows:
S3
S4
0
0
24H
0
1
10LUX
1
0
50LUX
1
1
100LUX
LUX
LUX:S3,S4
S3 S4
TIJD:S1,S2 LUX:S3,S4
S1 S2 S3 S4
1
0
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed
place.
Warning!
1. Being installed in the rocking object will lead to misoperation.
The following situation will lead to misoperation
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shada 800509 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shada 800509 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info