799267
12
Zoom out
Zoom in
Previous page
1/68
Next page
12
142 x 208 mm
Caution! Whenever the barbecue is not in use, the
heating element with the connection box must be
removed from the barbecue and stored in a dry
space indoors.
The other parts of the barbecue must not be stored
outdoors or in an open area where they could be
affected by the weather.
The grill may only be used with the supplied core
thermometer or the SEVERIN item no. ZB 8126.
No responsibility is accepted if damage results from
improper use, or if these instructions are not complied
with.
This product complies with all binding CE labelling
directives.
Before using for the rst time
Remove any packaging materials and stickers from the
appliance.
Cleanthegrillrack,reectortrayandthetrayinserts
with warm soapy water; wipe thoroughly dry afterwards.
Assemble the appliance as described in Preparing the
unit.
Let the grill heat up for approximately 10 minutes at
maximum power without any food (see ‘Boost-zone’
grilling). This will remove the smell typically encountered
whenrstswitchingonagrill.Alittlesmokemaybe
emitted; for that reason, adequate ventilation should
be ensured by opening windows or balcony doors; an
extractor hood is also suitable.
Grill assembly
Assemble the grill as shown in the diagrams:
Placethereectortrayintothegrillhousing.
Note: Fit the tray inserts so that each insert covers
four protrusions.
Fit the heating element with junction box into the
reectortray.Theapplianceisequippedwithasafety
switch. The unit can be operated only with the junction
box properly installed.
Fit both grill rack elements so that the studs on the
racktintothecorrespondingopeningsinthereector
tray.
Grill cart assembly
For grill models with grill cart, assemble the cart as
shown in the diagram.
For assembly, a Phillips screwdriver is needed.
Prior to assembly, check that all parts are complete as
listed in the Familiarisation section.
Assembly:
Placethegrillcartframeupside-downontheoor.
Insert the four support legs into the housing and
secure each support leg with two big bolts. The two
support legs with the additional holes for the wheels
must be mounted together on the narrow side of the
grill cart.
Turn the frame with the support legs upright.
Fit the plastic frame of the storage rack and secure it
on all four support legs, using the corresponding bolts
andnuts;thentthestoragerack.
Slide the wheel axles through the openings on the
support legs and put on the wheels. Secure each
wheel with one of the cotter pins and clip on the wheel
covers.
Fit the side tables onto the corresponding metal pins.
Ensure that the grill cart is stable. Check the bolts
regularlyforrmconnection.
Place the assembled grill on top.
Caution:
Do not exceed a maximum load of 3 kg for the side
tables, and 20 kg for the storage rack.
If you need to move the grill, remove the table on the
side opposite from the wheels and grip the frame.
Preparing the unit
Assemble the appliance as described in Grill assembly.
For grill models with grill cart, refer to Grill cart
assembly.
FillthereectortraywithwatertotheMax marking (max
2 litres). Do not pour water on the heating element or its
sensor.
Hint!
Duringgrilling,thewaterinthereectortrayshouldbe
replenished in good time. Caution: Always disconnect
theappliancefromthemainsbeforere-lling.
Connect the appliance to the mains.
The light ring lights up blue, the unit is ready for use.
Rotary control
The rotary control is used for function selection or switching
off (Sleep mode).
Turn:
Select the Function/Temperature/Timer.
Push - short:
Conrmtheselection.
Push - two seconds:
1 x: return to stand-by mode to change a function
2 x: return to sleep mode
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Severin PG 8137 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Severin PG 8137 in the language / languages: All languages as an attachment in your email.

The manual is 2.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info