Manual Severin PG 8119 - SEVO GS (page 11 of 64) (All languages)

799266

Zoom out

Zoom in

1/64

142 x 208 mm

Before using for the rst time

∙ Remove any packaging materials and stickers from the

appliance.

∙Cleanthegrillrack,reectortray,thetrayinsertsand

wind-guard with warm soapy water; wipe thoroughly dry

afterwards.

∙ Assemble the appliance as described in Preparing the

unit.

∙ Let the grill heat up for approximately 10 minutes at

maximum power without any food (see ‘Boost-zone’

grilling). This will remove the smell typically encountered

whenrstswitchingonagrill.Alittlesmokemaybe

emitted; for that reason, adequate ventilation should

be ensured by opening windows or balcony doors; an

extractor hood is also suitable.

Grill assembly

∙ Assemble the grill as shown in the diagrams:

∙Placethereectortrayintothegrillhousing.

∙ Note: Fit the tray inserts so that each insert covers

four protrusions.

∙Fit the heating element with junction box into the

reectortray.Theapplianceisequippedwithasafety

switch. The unit can be operated only with the junction

box properly installed.

∙Fit both grill rack elements so that the studs on the

racktintothecorrespondingopeningsinthereector

tray.

∙Fitthewind-guardelementsrstattherearintothe

recesses on the grill rack, and then secure them on

the grill rack frame.

Assembling the base stand

Assemblethebasestandasshowninthegure:

∙ Insert the four support legs into the frame from below

until they engage.

∙ Insert the storage grate and secure it to the support legs

with the four wing nuts.

∙ Check that the base stand is secure.

∙ Put on the assembled grill.

The maximum load of the storage grate is 9 kg.

Preparing the unit

∙Assemble the unit as described in “Grill assembly” and

“Assembling the base stand”.

∙FillthereectortraywithwatertotheMax marking (max

2 litres). Do not pour water on the heating element or its

sensor.

Hint!

Duringgrilling,thewaterinthereectortrayshouldbe

replenished in good time. Caution: Always disconnect

theappliancefromthemainsbeforere-lling.

∙ Connect the appliance to the mains.

∙ The light ring lights up blue, the unit is ready for use.

Rotary control

The rotary control is used for function selection or switching

off (Sleep mode).

Turn:

Select the Function/Temperature/Timer.

Push - short:

Conrmtheselection.

Push - two seconds:

1 x: return to stand-by mode to change a function

2 x: return to sleep mode

Rotary control - light ring

The light ring indicates the current operating mode:

No light:

The unit is in sleep mode.

Blue light:

The unit is in stand-by mode.

Flashing:

The grill rack has not yet reached the selected temperature.

The unit is heating up or cooling down.

Steady:

The selected temperature has been reached.

Orange:

Grilling 80-320 °C

Red:

Boost-zone 330-500 °C

Timer

The timer is used to monitor the grilling time. It can be set

from 1 min to 23 h 59 mins. Beep signals indicate that the

running time has elapsed; the heating element remains

switched on.

∙ Turn the rotary control until lights up.

∙Presstherotarycontrolbrieyandturntoselectthe

hours.

∙Presstherotarycontrolbrieyandadjusttheminutes.

∙Conrmthetimesettingbybrieypressingthecontrol.

Thecolonstartsashing;oncethetimehaselapsed,

beep signals are heard.

∙ To return to stand-by mode, press the rotary control for

two seconds.

∙ Alternatively, set the timer to 0:00, and press the control

brieytoreturntostand-bymode.

∙ If the heating is switched off after the timer is set, the

appliance will change to sleep-mode 5 minutes after the

last input, i.e. the timer is switched off.

∙ If the timer is set with the heating already off, it will

continue until the pre-selected time is reached, when the

unit changes to sleep-mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Severin PG 8119 - SEVO GS in the language / languages: All languages as an attachment in your email.

The manual is 2.23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Severin PG 8119 - SEVO GS Manual

Product: