603065
14
Zoom out
Zoom in
Previous page
1/40
Next page
14
the utmost care that they are properly aligned during re-
assembly.
Open the freezer door (18).
Remove the xing screws (1 and 3) from the top cover (two
screws at the front and two at the rear), and take off the
cover (4).
Unscrew the upper hinge bracket (5) and remove it.
Caution: the door must be supported while this is done.
Take off the freezer door (18).
Unscrew the hinge pin (7) together with the nut (6) and
washers (8), and t the entire assembly to the opposite side
of the hinge bracket.
Undo the xing screws (11) on the centre hinge bracket (10).
Caution: Support the door.
Take off the centre hinge bracket (10) together with the
hinge pin washers and the plastic plate (9).
Take off the refrigerator door (13).
Tilt the whole unit towards the rear.
Unscrew the lower hinge bracket (14) and take it off.
Unscrew the hinge pin (15) from the bracket, and re-insert it
from the other side.
Remove both screws on the left of the underside and
replace them on the right.
Fit the lower hinge bracket (14) on the left of the underside.
Put the washers on the hinge pin.
Remove the cap (19) from the freezer door and the cap (16)
from the refrigerator door and replace them on the opposite
side of the doors.
Take off the caps (17) from the partition between the
refrigerator and freezer compartments and remove the
screws.
Replace both screws on the opposite side and then the
caps.
Fit the refrigerator door (13) onto the pin (15) of the lower
hinge bracket.
Fit the pin of the centre hinge bracket (10), together with the
washers, to the refrigerator door (13).
Fit the centre hinge bracket (10) together with the plastic
plate (9).
Remove both screws from the upper left and replace them
on the right.
Place the freezer door (18) onto the pin of the centre hinge
bracket.
Fit the pin of the upper hinge bracket (5) to the freezer door
(18), and then t and secure the upper hinge bracket (5).
Note: If necessary, the alignment of the doors can be adjusted
by slightly loosening the hinge bracket screws, but remember
to tighten them afterwards
.
Replace the top cover (4) and use the screws (1 and 3) to
secure it (two screws at the front and two at the rear).
If the unit has been tilted to more than 30°, wait for about 4
hours before re-connecting it to the mains.
Temperature control
The unit is re-activated by connecting it to the mains. It is only
switched off completely when the plug is removed from the wall
socket.
The temperature in the refrigerator cabinet can be adjusted by
setting the temperature control. Turning the control clockwise
will decrease the temperature, while turning it anti-clockwise
will increase it.
The medium settings are usually most suitable for home use.
We recommend using a thermometer to check the actual
temperature inside the cabinet and make adjustments as
necessary.
Following a power interruption, or if the unit has been switched
off on purpose, it may take 3 to 5 minutes before it switches
on again.
In position ‘0’, the cooling function is switched off, though
the appliance is still connected to the mains.
1. Temperature control
2. Control panel cover
3. Bulb
4. Lamp cover
5. Locking mechanism
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Severin KS9793 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS9793 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info