Manual Severin KS9786 (page 14 of 40) (English, German, Dutch, French)

603062

Zoom out

Zoom in

1/40

the utmost care that they are properly aligned during re-

assembly.

∙ Open the freezer door (18).

∙ Remove the ﬁ xing screws (1 and 3) from the top cover (two

screws at the front and two at the rear), and take off the

cover (4).

∙ Unscrew the upper hinge bracket (5) and remove it.

Caution: the door must be supported while this is done.

∙ Take off the freezer door (18).

∙ Unscrew the hinge pin (7) together with the nut (6) and

washers (8), and ﬁ t the entire assembly to the opposite side

of the hinge bracket.

∙ Undo the ﬁ xing screws (11) on the centre hinge bracket (10).

Caution: Support the door.

∙ Take off the centre hinge bracket (10) together with the

hinge pin washers and the plastic plate (9).

∙ Take off the refrigerator door (13).

∙ Tilt the whole unit towards the rear.

∙ Unscrew the lower hinge bracket (14) and take it off.

∙ Unscrew the hinge pin (15) from the bracket, and re-insert it

from the other side.

∙ Remove both screws on the left of the underside and

replace them on the right.

∙ Fit the lower hinge bracket (14) on the left of the underside.

∙ Put the washers on the hinge pin.

∙ Remove the cap (19) from the freezer door and the cap (16)

from the refrigerator door and replace them on the opposite

side of the doors.

∙ Take off the caps (17) from the partition between the

refrigerator and freezer compartments and remove the

screws.

∙ Replace both screws on the opposite side and then the

caps.

∙ Fit the refrigerator door (13) onto the pin (15) of the lower

hinge bracket.

∙ Fit the pin of the centre hinge bracket (10), together with the

washers, to the refrigerator door (13).

∙ Fit the centre hinge bracket (10) together with the plastic

plate (9).

∙ Remove both screws from the upper left and replace them

on the right.

∙ Place the freezer door (18) onto the pin of the centre hinge

bracket.

∙ Fit the pin of the upper hinge bracket (5) to the freezer door

(18), and then ﬁ t and secure the upper hinge bracket (5).

Note: If necessary, the alignment of the doors can be adjusted

by slightly loosening the hinge bracket screws, but remember

to tighten them afterwards

∙ Replace the top cover (4) and use the screws (1 and 3) to

secure it (two screws at the front and two at the rear).

If the unit has been tilted to more than 30°, wait for about 4

hours before re-connecting it to the mains.

Temperature control

The unit is re-activated by connecting it to the mains. It is only

switched off completely when the plug is removed from the wall

socket.

The temperature in the refrigerator cabinet can be adjusted by

setting the temperature control. Turning the control clockwise

will decrease the temperature, while turning it anti-clockwise

will increase it.

The medium settings are usually most suitable for home use.

We recommend using a thermometer to check the actual

temperature inside the cabinet and make adjustments as

necessary.

Following a power interruption, or if the unit has been switched

off on purpose, it may take 3 to 5 minutes before it switches

on again.

In position ‘0’, the cooling function is switched off, though

the appliance is still connected to the mains.

1. Temperature control

2. Control panel cover

3. Bulb

4. Lamp cover

5. Locking mechanism

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS9786 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Severin KS9786 Manual

Product: