556613

Severin KS 9875 Manual

33
Zoom out
Zoom in
Previous page
1/64
Next page
Preparing the appliance for operation
! It is recommended to prepare the appliance for operation with a helper.
Remove package. Lift the appliance away from foamed polystyrene base. Tear off adhesive tapes.
When positioning the appliance in chosen location, it will move more easily into position if you lift the front a
little and incline it backward, allowing it to roll on its casters.
Remove all red-coloured parts from the
shelves (
fig. 2). Tear away the red-
coloured adhesive tapes from the door
trays – they are intended only for the
transport of the appliance.
NOTE. When you open the freezer
compartment door a little red packing
detail will fall out – IT IS FOR TRANSPORTATION PURPOSES ONLY.
Suitably dispose the packaging material.
Take two supports from the bag and insert them into the guides at the top back
part of the appliance.
►
Positioning
Place the appliance in a dry, well ventilated room.
WARNING! The appliance should not be operated in an unheated room or porch. Place the appliance away
from heat sources such as kitchen stove/oven, radiators, or direct sunlight.
WARNING! The appliance must not touch any pipes for heating, gas or water supply, or any other
electrical devices.
Do not cover the ventilation holes at the top of the appliances– it must be a good air
circulation around the appliance. There should be a gap of at least 10 cm between the
top of the appliance body and any furniture that may be above it (
fig. 5). If this
requirement is not followed, the appliance consumes more electrical energy and its
compressor may overheat.
◄ If the appliance is placed in a corner,
a gap of at least 1 cm must be left
between the appliance body and the
wall so that the freezer compartment
door can be opened enough to pull out
the frozen product drawer.
The appliance must stand on a level
surface and must not touch the wall.
If necessary, regulate the height of
the appliance by adjusting the
levelling feet: by turning them
clockwise – the front of the appliance
rises, by turning them counter clockwise – it comes down. If
the appliance is tilted slightly backward – the doors will
close by themselves.
Changing the interior light bulb
When changing the interior light bulb, do the actions below in the order they are
listed:
1.
Unplug the appliance from the mains by pulling the plug out of the
electricity supply socket
.
2. Squeeze the sides of the light fixture cover
1 to unhook the cover fasteners A
and pull downward. Remove the cover.
3. Replace the light bulb with the same 15 W type light bulb with the E14 lamp holder.
4. After changing the light bulb, put the cover fastener hook in place
B and then press upward until it’s fixing
in place. Plug the appliance into the electricity supply socket.
KS 9870 / 71 KS 9897 / 98 / 99 / 9770
KS 9865 / 66 / 67 / 68 KS 9874 / 72 / 73KS 9865 / 66 / 67 / 68 KS 9874 / 72 / 73
GB
32
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Severin KS 9875 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS 9875 in the language / languages: English, German, Dutch, French, Swedish, Spanish as an attachment in your email.

The manual is 24,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info