556628

Severin KS 9829 Manual

15
Zoom out
Zoom in
Previous page
1/100
Next page
– Use a suitable screw-driver to remove the screw holding the light cover and take the cover off to
the back.
– Take out the defective bulb and fit a new one (max. 15 W).
– Slide the cover back into position, replace the screw and tighten it.
– Connect the unit to the mains power. It may take 3 to 5 minutes before it switches on again.
Storing food
– The temperature inside the refrigerator depends mainly on the ambient temperature, the
temperature control setting and the amount of food stored.
– Different areas of the refrigerator cabinet are affected differently by the cooling effect. The
warmest area is around the door in the higher part of the cabinet, the coldest around the rear wall
and in the lower part of the cabinet.
– The food should therefore be stored as follows:
– On main cabinet shelves (from top to bottom): bakery items, ready meals, dairy products, meat,
fish and cold meats/sausages.
– In the vegetable compartment: vegetables, salad and fruit.
– In the door (from top to bottom): butter, cheese, eggs, tubes (eg mustard), small bottles, large
bottles, milk and fruit-juice tetra-packs.
– Initially, the temperature control should be set to position 4. If the cooling effect is too strong,
lower it to position 1-3; if it is insufficient, raise it to 5-7.
If you notice frost on the rear wall, the most likely cause is that the door has been left open
for too long, or that warm food has been placed inside the refrigerator or that the
temperature control has been set too high.
– Liquid or strong-smelling food, or food which is likely to absorb strong odours (e.g. cheese, fish,
butter), should be stored separately or in hermetically sealed containers.
– Warm food should be left to cool down to room temperature before being placed in the
refrigerator.
– Always ensure that the door is properly closed and that the seal is not obstructed by food stored
inside the cabinet or door.
De-frosting and cleaning
The integral vapouriser is sealed in foam in the rear wall; you may therefore notice a build-up of frost
around the rear area. This layer of frost will start melting when the compressor is not working.
Through a system of hoses, the melt-water drains into the collection tray below the compressor, where
it will be absorbed into the surrounding air. The unit does not therefore require de-frosting, but only
proper cleaning instead.
To enable the melt-water to drain freely, always ensure that the channel and discharge opening in the
cabinet are free of any blockage.
– Always remove the plug from the wall socket before cleaning.
– Do not pour water over or inside the unit.
15
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Severin KS 9829 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Severin KS 9829 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info