471981
8
Zoom out
Zoom in
Previous page
1/27
Next page
1514
ባቤ
¾
µ
ƽ
ƻ
¸¹
ƹ
Ƹ
Connections and operating elements of the SZI 1015
RF input (BNC socket)
Mono/multi switch
RF output (BNC socket)
Thread for mounting the radiator
Barrier strip RF contacts, input (wired in parallel with )
Barrier strip DC inputs – for powering from the SI 1015 modulator
or via the NT 1015 plug-in mains unit
Barrier strip DC outputs (for daisy-chaining a second SZI 1015)
Barrier strip RF contacts, output (wired in parallel with )
1 Cable grip
Insert the connector of the plug-in mains unit into socket ƽ on the SI 1015 modulator and pass
the cable through the cable grip ƻ as shown. Because of the cable grip, the connector cannot slip
out of the socket and interrupt operation.
Note
A cable grip is particularly important when the device is permanently rack mounted.
Inside the rack there are often a large number of cables – a cable grip prevents the
cables from pulling each other out.
2 Rack mounting
The SI 1015 can be rack mounted into 1 U of a 19” rack by using accessories GA 1031-AM or
GA 1031-CC. The GA 1031-CC is a blank module to bring the SI 1015 to full 19” width, the
GA 1031-AM is identical but has additional BNC sockets to bring outputs ¾ and ƹ to the front
panel. The rack mountings are supplied with the SI 1015.
3 Connecting the SZI 1015 radiators
Sockets ¸ and ƺ on the SI 1015 modulator can be used to connect two SZI 1015 power radiators.
For connecting the radiators, use ready made up co-axial cables with BNC connectors.
You can also use a co-axial cable without a connector. The cable has to be inserted into contacts µ
and Ƹ of the barrier strip. Remove approx. 20 mm of the cable‘s cuter jacket, twist the screen into
a little roll, and pull it to one side. Strip the central wire by approx. 10 mm. Insert the screen into
the ground terminal and the central wire into the indicated contact on the barrier strip.
4 Daisy-chaining the radiators
Two SZI 1015 power radiators or one SZI 1029-24 high power radiator can be 25-29 V DC
powered by the NT 1015 plug-in mains unit via the SI 1015 modulator. The supply voltage is
output via the two contact pairs ¸+¹. Connect the radiators to the contacts by using a two-wire
cable with a cross section of 1.5 mm
2
per wire.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sennheiser SZI 1015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sennheiser SZI 1015 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info