12/2018
- 5 -
Copyright © 2018, F
EN
V
Elec
User'smanual
■ Prior to using this appliance, please r manual thoroughly
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described in
this user’smanual
retrieved for future r
■ We rec
purchase receipt and responsibility statement of the v
for at least the duration of the legal liability for unsatisfactory performance
or quality. In the event of transportation, we rec
appliance in the original box from the manufacturer
DESCRIPTION OF
A1 Open lid button
A2 Lid
A3 Spout
A4 Filtration strainer
(cannot be removed)
A5 Water lev
A6 Base with acentral connector
A7 Control panel
A8 Handle
A9 LED light for the inside of the
kettle
DESCRIPTION OF
B1 T
B2 On/O button
B3 Set temperature button – 50, 70, 80 or 90
BEFORE FIRST USE OF
1. Remove all wrapping material from the kettle and its base A6 .
2. Fill the kettle with clean water up t
and empty the contents of the kettle. Repeat this process 2 t
Note:
T
in chapter Using the kettle.
3. Now the kettle is ready for operation.
USING THE KET
1. Set the desired length of the power cord. Push the pow
in the base A6 . Place the base A6 on astable, even and clean surface.
2. Press button A1 to open the lid A2 , then ll the kettle with the required amount
of water
not exceed the maximum mark (2l). After lling it, close the lid A2 and make
sure that it is secured in the closed position.
Attention:
Do not ll the kettle when it is placed on the base A6 .
When lling the kettle, there is arisk of water splashing out.
3. PlacA6 and insert the power cord plug into a
socket. When the po
be made and all the LED indicators B1 and the LED light A9 will light up for an
instant and another beep will be made.
mode and is ready for use.
4. P
4.1 Boil
■ TB2 . A
button was pressed.
A9 is lit red.
TwA9 will turn o.
Note:
The water boiling process can be st
button B2 .
4.2
■ Use button B3 to set the heating temperatur
temperature setting changes each time button B3 is pressed
button is accompanied by ashort beep.
the respective LED indicator B1 being lit.
to the set temperature, prB2 . LED light A9 will be lit:
– green when temperature is set t
– blue when temperature is set to 70
– violet when temperature is set to 80
– orange when temperature is set to 90
■ When the water is heated to the set temper
automaticallyA9 will turn o
indicator B1 remains lit for appr
it turns o and the kettle switches to the stand-by mode.
Note:
If you set atemperaturB3 and then do not press button B2
to start the water heating process, after 15 seconds the kettle will switch
to the stand-by mode and the respective LED indicator B1 will turn o
The temperature setting can be changed while the appliance is running
The process of heating water t
time by again pressing button B2 .
If you set atemperature that is low
water inside the kettle, aB2 is pressed and
the kettle will turn o automatically
4.3
■ This mode is usually used when you wish to heat water t required
temperature and then maintain it at this tempera
water and then keep it warm.
■ Use button B3 to select the required temperatur
respective LED indicator B1 will be lit. PrB2 and hold it down for
approx. 3 seconds. B1 will start ashing, the
coloured LED light A9 will be lit as described in point 4.2 and the process of
heating water to the set temperatur
reached, two beeps are made and the kettle automatically swit
warm mode. In this mode, the heating element automatically switches on and
o to maintain the set temperature
after 30 minutes. A9 and the r
LED indicator B1 will turn o, and the kettle will swit
■ Using the above described method, it is possible to set the keep warm mode
after previously boiling or heating water accor
4.2. If, for this mode
temperature inside the kettle, two beeps will be made when the kettle is started.
This signals that the set temperature has alr
down to the set temperature and will then be maintained a
The keep warm mode ends automatically after 30 minutes.
■ T
press and hold down button B2 for 3 seconds
atemperature of 50
Note:
If you set atemperaturB3 and then do not press button B2
to start the maintain set temperature mode, after 15 seconds the kettle
will switch to the stand-by mode and the respective LED indicator B1 will
turn o.
It is not possible to change the set temperature in the keep warm mode.
The keep warm mode can be stopped at any time by prB2 .
Attention:
If the kettle is not located on the base A6 , the buttons on the control
panel A7 will not react to being pressed.
Lifting the kettle o the base will cancel all previous settings.
kettle is placed back on to the base A6 , ashort beep will be made and all
the LED indicators B1 and the LED light A9 will light up for an instant and
another beep will be made.
mode and is again ready for use.
This kettle is not calibrated for scientic or labora
water temperature ma
Attention:
Do not turn on the kettle when it is empty. Incorrect use may negatively
aect its lifetime. If you accidentally turn on the kettle without wat
inside, after ashort time aA9 will turn
o and the kettle will turn o.
This is indicated by aB1 and the LED
light A9 turning on for an instant. Then the kettle will swit
mode and is again ready for use.
5. Pour the boiled or heat
sure that the kettle remains in a
it is lled all the way up to the maximum mark.
6. If you wish to open the kettle to rell it, be especially careful when opening the
lid A2 to avoid scalding by the escaping steam.
7. After you nish using it, disconnect the power cord fr
Empty the kettle and allow it to cool down.
CLEANING AND MAINTENANCE
1. Removing limescale deposits
■ Limescale deposits inside the kettle may negatively aect its lifetime
important to regularly remove it based on how frequently the kettle is used
During standard use (3 to 5 times per day), we recommend w
be removed:
– once per month in areas with hard and very hard water;
– once every two to three months in areas with soft and medium hard water
