759120
5
Zoom out
Zoom in
Previous page
1/6
Next page
04/2017
- 5 -
Copyright © 2017, Fast ČR, a.s.
EN
Variable Temperature
Electric Kettle
User'smanual
Prior to using this appliance, please read the usersmanual thoroughly, even
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described
in this user’smanual. Keep this usersmanual in asafe place where it can be
easily retrieved for future reference.
We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty
card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend that
you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE KETTLE
A1 Open lid button
A2 Lid
A3 Spout
A4 Water level mark
A5 Base with acentral connector
A6 Control panel
A7 Handle
A8 Internal LED light
DESCRIPTION OF THE CONTROL PANEL
B1 Temperature setting LED indicators
B2 Set temperature touch button – 60, 70, 80 and 90 °C.
B3 On/Off touch button
BEFORE FIRST USE OF THE KETTLE
1. Remove all wrapping material from the kettle and its base A5.
2. Fill the kettle with clean water up to the maximum water mark. Boil the
water and empty the contents of the kettle. Repeat this process 2 to 3 times.
Note:
To boil water in the kettle proceed according to the instructions in
chapter Using the kettle.
3. Now the kettle is ready for operation.
USING THE KETTLE
1. Set the desired length of the power cord. Push the power cord into the
groove in the base A5. Place the base A5 on a stable, even and clean
surface.
2. Fill the kettle with the required amount of water. To open the lid A2, press
button A1. The water level must reach at least the minimum mark (0.5l) but
must not exceed the maximum mark (1.8l). After filling it, close the lid A2
and make sure that it is secured in the closed position.
Attention:
Do not fill the kettle when it is placed on the base A5.
When overfilling, there is arisk of boiling water splashing out.
3. Place the kettle on the base A5 and insert the power cord plug into apower
socket. When the power cord is connected to apower socket, ashort beep
is made, the control panel A6 and the LED light A8 is lit for a brief moment.
The kettle will then switch to standby mode and is ready for use. In standby
mode, the red indicator on button B3 will flash.
4. Operating mode settings:
4.1
Boil water mode
To start the water boiling process, press button B3. Asound signal confirms
that the button was pressed. The indicator on button B3 will be lit, the kettle
will start heating water to 100 °C. During operation, the LED light A8 is lit
red. When the water comes to aboil, the kettle will turn off automatically,
LED light A8 will turn off and the indicator on button B3 will start flashing.
Note:
The water boiling process can be stopped at any time by again
pressing button B3 or lifting the kettle off the base A5.
4.2
Boil water then keep warm mode
Press button B3 and hold it down for approx. 2 seconds. Asound signal will
be made and the indicator on buttons B2 and B3 will be lit. The kettle will
start heating water to 100 °C. During operation, the LED light A8 will flash
red.
Once the water has come to aboil, a sound signal will be made and the
kettle will automatically switch to the keep warm mode. The LED light A8
flashes constantly and the indicators on buttons B2 and B3 remain lit. In this
mode, the heating element automatically switches on and off to maintain
temperature. The time of keep warm mode is preset to 120minutes. After
this time has elapsed, the kettle will turn off automatically. If you wish to end
this mode sooner, press button B3 or lift the kettle off the base A5.
4.3
Heat water to set temperature mode
Press button B3 and then use button B2 to select the desired temperature
of 60, 70, 80 or 90 °C. The temperature setting changes each time the button
is pressed, and is indicated by the respective indicator B1 being lit. Each
press of the button is accompanied by ashort beep. The kettle will heat the
water to the selected temperature and during operation the LED light A8
will be lit:
green when the temperature is set to 60 °C.
blue when the temperature is set to 70 °C.
yellow when the temperature is set to 80 °C.
violet when temperature is set to 90 °C.
When the set temperature is reached, the kettle will turn off automatically.
The respective indicator B1 will be flashing on the control panel A6 and
the control buttons are not lit. After 2 minutes the kettle will switch to the
standby mode.
Note:
The temperature setting can be changed while the appliance is
running.
If you set alower temperature than the current temperature of the
water inside the kettle, asound will be made and the kettle will turn
off automatically.
4.4
Heat water to set temperature then keep warm mode
Press button B3 and hold it down for approx. 2 seconds. Asound signal is
made. Use button B2 to select the desired temperature of 60, 70, 80 or 90 °C.
The temperature setting changes each time the button is pressed, and is
indicated by the respective indicator B1 being lit. Indicator lights B2 and
B3 will be lit. The kettle will heat the water to the selected temperature and
during operation the LED light A8 will be flashing:
green when the temperature is set to 60 °C.
blue when the temperature is set to 70 °C.
yellow when the temperature is set to 80 °C.
violet when temperature is set to 90 °C.
When the set temperature is reached, a sound signal will be made and
the kettle will switch to the keep warm mode. The LED light A8 flashes
constantly and the indicators on buttons B2 and B3 and the respective
indicator B1 remain lit. In this mode, the heating element automatically
switches on and off to maintain the set temperature. The time of keep warm
mode is preset to 120 minutes. After this time has elapsed, the kettle will
turn off automatically. If you wish to end this mode sooner, press button B3
or lift the kettle off the base A5.
Attention:
If the kettle is not located on the base A5, the control buttons B2 and
B3 will not react to being pressed.
Lifting the kettle off the base will cancel all previous settings. When
the kettle is put back on the base A5, the kettle will switch to standby
mode and is again ready for use.
This kettle is not calibrated for scientific or laboratory purposes. The
actual water temperature may differ by ±5 °C from the set water
temperature.
Attention:
Do not turn on the kettle when it is empty. Incorrect use may
negatively affect its lifetime. If you accidentally turn on the kettle
without water, it will turn itself off within afew moments. Wait until
the heating element cools down. This is indicated by a sound, the
control panel A6 and the LED light A8 being lit for an instant. Then
the kettle will switch to standby mode and is again ready for use.
5. Pour the boiled or heated water into a prepared container, cup or mug.
Make sure that the kettle remains in avertical position when it is carried,
particularly if it is filled all the way up to the maximum mark.
6. If you wish to refill the kettle, be careful not to scald yourself on the escaping
steam or to burn yourself on the hot surface of the lid A2 when opening or
closing it.
7. After you finish using it, disconnect the power cord from the power socket.
Empty the kettle and allow it to cool down.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SWK 1890 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SWK 1890 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sencor SWK 1890

Sencor SWK 1890 User Manual - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info