759059
7
Zoom out
Zoom in
Previous page
1/10
Next page
Electric kettle
SWK 1010WH / SWK 1011GR / SWK 1012BL / SWK 1013OR / SWK 1014RD / SWK 1015VT / SWK 1016YL / SWK 1017TQ / SWK 1018RS
EN
EN-7
2016 07/2016
BEFORE FIRST USE
1. Remove all wrapping material from the kettle and its base.
2. Fill the kettle with clean water up to the maximum water mark. Boil the water and empty the
contents of the kettle. Repeat this process 2 to 3 times.
Note:
To boil water in the kettle proceed according to the instructions in chapter Using the kettle.
3. Now the kettle is ready for use and for preparing warm beverages, etc.
USING THE KETTLE
1. Set the desired length of the power cord. Push the power cord into the groove in the base A4. Place
the base A4 on a stable, even and clean surface.
2. Fill the kettle with the required amount of water. The water level must reach at least the minimum mark
(0.3 l) and must not exceed the maximum mark (1 l). You may fill the kettle through the spout or through
the opening after lifting the lid A1. To open the lid A1, press button A2. After filling the kettle with
water, close the lid A1 and push it down so that it is secured in the closed position.
Warning!
Never fill the kettle if it is located on the base A4.
If the kettle is overfilled, then boiling water could splash out.
3. Place the kettle on the base A4. Insert the power plug into the an electrical power socket. Check
that the lid A1 of the kettle is closed.
4. Start the kettle by moving the switch A5 to position I (On). The power On light A8 will illuminate.
Attention:
Do not turn on the kettle if it is empty. The incorrect use of the kettle may negatively affect its
lifetime. If you accidentally turn on the kettle without water, the thermostat will, after reaching
a certain temperature, interrupt the electric circuit and the power On light A8 will turn off. The
kettle can be used again after several minutes, as soon as its stainless steel bottom has cooled
down.
5. As soon as water boils the kettle will turn off automatically and the power On light A8 will turn
off. Before taking the kettle off the base A4, check that it has turned itself off automatically. If it
has not automatically turned itself off, turn off the kettle manually by moving the switch A5 to
position 0 (Off).
Note:
The operation of the kettle can be interrupted at any time by moving the switch A5 to position
0 (Off).
6. Pour the boiled water into a prepared container, cup or mug. Make sure that the kettle remains in
a horizontal position when it is carried, particularly if it is filled all the way up the maximum mark.
If you wish to open the lid A1 to refill the kettle, first empty all the contents from the kettle so that
you are not scalded by the escaping steam.
7. After you finish using the kettle, disconnect the power cord from the el. power socket. Empty the
kettle and allow it to cool down.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SWK 1010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SWK 1010 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info