759483
5
Zoom out
Zoom in
Previous page
1/6
Next page
- 5 - 07/2020
Copyright © 2020, Fast ČR, a.s.
EN Vacuum Cleaner
User'smanual
A1 Cord winding button
A2 Full dust bag indicator
A3 Vacuum hose connection hole
A4 Clip for locking and releasing the
lid
A5 Button for opening the accessory
compartment
A6 Buttons +/- serve to control the
power of the motor.
A7 START/STOP button
A8 Rubber-coated wheel
A9 Handle
A10 Sliding ap for air suction
A11 Telescopic tube
A12 Clip for the telescopic tube
A13 Floor nozzle
A14 Flap position for vacuuming
carpets
A15 Flap position for vacuuming hard
(smooth) oors
A16 Hose
A17 Accessory holder (depending on
the model)
A18 Stopper for the horizontal and
vertical parking position
A19 Clip
A20 Hose end
A21 Horizontal parking position
A22 Power cord
A23 Carry handle
A24 Front travel wheel with swivel
mechanism
A25 Vertical parking position
A26
Telescopic slot nozzle for vacuuming
in hard to reach places (e.g. windows,
corners, book shelves, areas between
mattresses, upholstery, etc.)
A27 Upholstery nozzle with an
additional brush
A28 Hard oor nozzle
A29 Mini turbo brush
A30 Long exible crevice nozzle
A31 Dust bag collar
A32 Dust bag
A33 Dust bag holder
A34 Inow micro-lter
A35 Grill of the inow micro-lter
A36 Outow micro-lter
A37 Outow HEPA lter
A48 Grill of the outow micro-lter
and HEPA lter
ASSEMBLY
Inserting the hose into the air suction hole on the vacuum cleaner:
Press both the safety buttons on the end of the hose A20 end and insert the hose end
A20 into the air suction opening A3 on the vacuum cleaner until you hear a“click”. The
hose A16 is now secured in the correct position.
Attach the holder to the telescopic tube:
Make sure to place the holder with the hose on the wider part of the telescopic tube A11.
Attach the oor nozzle to the telescopic tube:
Make sure the oor nozzle A13 is attached the narrower part of the telescopic tube A11.
Adjust the length of the telescopic tube:
Adjust the length of the telescopic tube A11 as required – disengage and hold the clip
A12 on the tube A11 in the direction shown by the arrow and adjust the length of the
tube A11 as required. Then release the clip A12 and slide out the tube A11 slightly
forward until you hear aclick”. The telescopic tube A11 is now securely xed in position.
USING THE VACUUM CLEANER
Connecting your vacuum cleaner to the power grid
Wind out the required length of the power cord A22 by pulling on the power plug. Insert
the power plug into apower socket.
Caution:
Yellow marking on the power cord warns that the power cord
is close to its end. Do not pull the cord further than the red
marking.
Adjusting the oor inlet nozzle according to the oor surface.
You may set the inlet nozzle A13 according to the oor surface by adjusting the inlet ap:
If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle,
by turning the ap accordingly.
If you want to vacuum hard and smooth surfaces, extend the bristles out of the
nozzle, by turning the ap accordingly.
Turning your vacuum cleaner on and o
To switch your vacuum cleaner on, press the START/STOP button A7. To turn o the
vacuum cleaner, press the button A7 again.
Adjusting the suction power
Suction can be controlled using buttons +/- A6. The power of the vacuum cleaner is
increased using the + button, decreased using the - button. In asmaller range, you may
regulate suction power using the mechanically sliding ap A10 on the hose handle A9.
Tips
• Use the maximum suction strength when vacuuming carpets
or oors with a hard surface. Use the reduced strength when
vacuuming upholstery, window curtains, etc.
If the hose holder A9 becomes blocked when vacuuming,
disconnect it from the telescopic tube A11 and also disconnect
the hose A16 from the vacuum cleaner body. Then place the
holder inside the suction hole on the vacuum cleaner body and
vacuum out the stuck dirt.
Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for awhile, you can use the horizontal A21 or vertical
A25 parking position on the vacuum cleaner, into which you insert the stopper A18
on the oor nozzle A13.
Attention:
Do not move the vacuum cleaner from place to place if the hose
A16 is in the parked position! The stopper A18 on the oor
nozzle A13 could brake o.
Ending the vacuuming process
When you nish vacuuming, switch the vacuum cleaner o by pressing the START/STOP
button A7 and then disconnect the power cord plug from the socket.
To wind the power cord A22 back into the vacuum cleaner, press and hold the winding
button A1 with one hand and guide the power cord A22 with the other.
Tip:
If the winding process stops and part of the power cord A22 is still outside,
release the winding button A1 and pull the cable out again by about
50 cm and then press and hold the winding button A1 again and repeat
the winding process.
Carrying the vacuum cleaner
It is possible to hold and carry the vacuum by the handle A23.
USING THE ACCESSORIES
The hard oor nozzle A28 ensures perfect and yet gentle vacuuming of smooth hard
surfaces thanks to the brush being from 100% natural bristles. It can be used to vacuum
oors that are sensitive to scratching such as wooden or oating oors, marble oors,
tiles, linoleum, etc.
The mini turbo brush A29 is the ideal helper for removing animal fur, hair, etc., while
at the same time being suitable for vacuuming hard-to-reach places. Its use is not
limited to the home, and can be used for vacuuming the car. It quickly and eectively
removes hair, animal fur and other materials from car seats, upholstery, pillows and
other textile surfaces.
The long exible crevice nozzle A30 serves to vacuum very hard-to-reach places
anywhere in your car.
CLEANING AND MAINTENANCE
Caution:
Before cleaning, disconnect this appliance from the power
source.
Changing the dust bag
When the full dust bag indicator A2 lights up, it is necessary to replace the dust bag A32.
If you do not remove the dust bag A32, the suction power will be reduced.
1) Open the vacuum cleaner lter area by pressing the lid clip A4 while pulling it upwards
at the same time.
2) By pulling on the collar A31 of the dust bag in the direction of the arrow, remove it
from the plastic holder A33 and insert anew bag.
3) Close the lid of the vacuum cleaner, until you hear aclick.
Replacing and cleaning the inow micro-lter and outow HEPA lter and micro-lter
1) Open the vacuum cleaner lter area by pressing the lid clip A4 while pulling it upwards
at the same time.
2) By pulling on the collar A31 of the dust bag in the direction of the arrow, remove it
from the plastic holder A33 to make room for the removal of the lter.
3)
Pull the inow micro-lter grill A35 towards yourself and take out the micro-lter A34.
4) Simultaneously press both PUSH buttons at the rear of the vacuum cleaner. This will
tilt out the rear grill A38 of the outow micro-lter and HEPA lter. Put the grill A38
aside and take out both lters.
5) If the micro-lters are A34, A36 slightly soiled, it is possible to wash them under
running lukewarm water. If the HEPA lter A37 is slightly soiled, it is possible to
quickly wash it under aweak current of running lukewarm water. This will remove
dust and dirt found on its surface. In the event of heavy soiling, replace the lters
with new ones.
6) Allow washed lters A34, A36 to dry naturally. Do not dry them over heaters or using
hair dryers. Then put the inow micro-lter A34, outow HEPAlter A37, micro-lter
A36 and the grills back in their place.
7) Return the dust bag A32.
8) Close the lid of the vacuum cleaner, until you hear aclick.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SVC 7550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 7550 in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info