759477
9
Zoom out
Zoom in
Previous page
1/12
Next page
Vacuum Cleaner
SVC 6900GR 4AAAA ECO POWER
EN
EN-9
Copyright © 2019, Fast ČR, a.s. Revision 05/2019
Adjusting the oor inlet nozzle according to the oor surface.
You may set the inlet nozzle A13 according to the oor surface by adjusting the inlet ap:
If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle, by turning the ap
accordingly.
If you want to vacuum hard and smooth surfaces, extend the bristles out of the nozzle, by turning the ap
accordingly.
Turning your vacuum cleaner on and o
To switch your vacuum cleaner on, press the START/STOP button A7. To turn o the vacuum cleaner, press the button
A7 again.
Adjusting the suction power
Suction power can be controlled using the electronic power control dial A6. Turn the power control dial A6 clockwise
to the MAX position to increase the power of the vacuum cleaner, turn it in the opposite direction to the MIN position
to reduce its power. In asmaller range, you may regulate suction power using the mechanically sliding ap A10 on
the hose handle A9.
Tips
• Use the maximum suction strength when vacuuming carpets or oors with ahard surface. Use the
reduced strength when vacuuming upholstery, window curtains, etc.
If the hose holder A9 becomes blocked when vacuuming, disconnect it from the telescopic tube
A11 and also disconnect the hose A16 from the vacuum cleaner body. Then place the holder inside
the suction hole on the vacuum cleaner body and vacuum out the stuck dirt.
Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for awhile, you can use the horizontal A21 or vertical A25 parking position on the
vacuum cleaner, into which you insert the stopper A18 on the oor nozzle A13.
Attention:
Do not move the vacuum cleaner from place to place if the hose A16 is in the parked position! The
stopper A18 on the oor nozzle A13 could brake o.
Ending the vacuuming process
When you nish vacuuming, switch the vacuum cleaner o by pressing the START/STOP button A7 and then disconnect
the power cord plug from the socket.
To wind the power cord A22 back into the vacuum cleaner, press and hold the winding button A1 with one hand and
guide the power cord A22 with the other.
Tip:
If the winding process stops and part of the power cord A22 is still outside, release the winding button A1
and pull the cable out again by about 50 cm and then press and hold the winding button A1 again and
repeat the winding process.
Carrying the vacuum cleaner
It is possible to hold and carry the vacuum by the handle A23.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SVC 6900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 6900 in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info