759467
8
Zoom out
Zoom in
Previous page
1/14
Next page
EN-8
EN
Vacuum Cleaner
SVC 682VT / SVC 684TQ
Copyright © 2016, Fast ČR, a.s. Revision 01/2016
USING THE VACUUM CLEANER
Connecting your vacuum cleaner to the power grid
Wind out the required length of the power cord by pulling on the power plug. Insert the power plug
into a power socket.
Caution:
Yellow marking on the power cord warns that the power cord is close to its end. Do not pull the
cord further than the red marking.
Adjusting the floor inlet nozzle according to the floor surface.
You may set the inlet nozzle according to the floor surface by adjusting the inlet flap:
If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle, by turning the
flap accordingly.
If you want to vacuum hard and smooth surfaces, extend the bristles out of the nozzle, by turning
the flap accordingly.
Turning your vacuum cleaner on and off
To switch your vacuum cleaner on, press the START/STOP button. To turn off the vacuum cleaner, press
the button again.
Adjusting the suction power
Suction power can be controlled using the electronic power control dial. Turn the power control dial
clockwise to the MAX position to increase the power of the vacuum cleaner, turn it in the opposite
direction to the MIN position to reduce its power. In a smaller range, you may regulate suction power
using the mechanically sliding flap on the hose handle.
Tips
Use the maximum suction strength when vacuuming carpets or floors with a hard surface.
Use the reduced strength when vacuuming upholstery, window curtains, etc.
If the hose holder becomes blocked when vacuuming, disconnect it from the telescopic tube
and also disconnect the hose from the vacuum cleaner body. Then place the holder inside
the suction hole on the vacuum cleaner body and vacuum out the stuck dirt.
Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for a while, you can use the horizontal or vertical parking position
on the vacuum cleaner, into which you insert the stopper on the floor nozzle.
Attention:
Do not move the vacuum cleaner from place to place if the hose is in the parked position! The
stopper on the floor nozzle could brake off.
Ending the vacuuming process
When you finish vacuuming, switch the vacuum cleaner off by pressing the START/STOP button and then
disconnect the power cord plug from the socket.
To wind the power cord back into the vacuum cleaner, press and hold the winding button with one hand
and guide the power cord with the other.
Tip:
If the winding process stops and part of the power cord is still outside, release the winding
button and pull the cable out again by about 50 cm and then press and hold the winding button
again and repeat the winding process.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SVC 684 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 684 in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info