Manual Sencor SVC 6001 (page 6 of 7) (English)

759472

Zoom out

Zoom in

1/7

- 6 - 05/2019

EN Bagged Vacuum Cleaner

User'smanual

■ Prior to using this appliance, please read the user’smanual thoroughly,

even in cases, when one has already familiarised themselves with

previous use of similar types of appliances. Only use the appliance in

the manner described in this user’smanual. Keep this user’smanual in

asafe place where it can be easily retrieved for future use.

■ We recommend saving the original cardboard box, packaging material,

purchase receipt and responsibility statement of the vendor or warranty

card for at least the duration of the legal liability for unsatisfactory

performance or quality. In the event of transportation, we recommend

that you pack the appliance in the original box from the manufacturer.

DESCRIPTION OF THE VACUUM CLEANER AND ITS ACCESSORIES

A1 Removable grill of the outflow

HEPA filter

A2 Washable outflow HEPA filter

is placed behind the grill.

A3 Automatic power cord

winding button

A4 Electronic suction power

control

A5 Full dust bag indicator

A6 Flexible hose connection hole

A7 Top cover locking and

releasing clip

A8 Integrated handle

A9 On/Off button of the vacuum

cleaner

A10 Rubber-coated rear travel

wheel

A11 Front swivel travel wheel

A12 Groove for the vertical

parking position

A13 Groove for the horizontal

parking position

A14 Dust bag*

A15 Dust bag holder

A16 Grill of the inflow micro-filter

A17 Washable inflow micro-filter is

placed in the grill.

A18 Flexible hose with mechanical

suction power control in the

handle

A19 Telescopic metal tube

A20 Floor nozzle with an

extensible brush

A21 2-in-1 brush and slot nozzle

Note*:

One disposable microfibre (nonwoven textile) bag is

included.

PREPARING FOR USE

■ Make sure that the dust bag A14, inflow micro-filter A17 and outflow

HEPA filter A2 are properly installed.

■ Slide the end of the flexible hose A18 fully into the hole A6.

Note:

When disassembling, it is necessary to press both locking

clips at the end of the hose A18 while at the same time

pulling the hose A18 out of the hole A6.

■ On to the handle of the flexible hose A18, place the telescopic tube

A19 and set it to the required length as follows. Release the clip on the

telescopic tube A19 and slide it towards the extensible part of the tube

A19. After releasing the clip, set the length of the tube A19 by sliding

its extensible part in or out. When the clip is released, it will lock in at

the set length.

■ Connect the floor nozzle A20 to the free end of the telescopic tube A19.

The flap on the floor nozzle A20 serves to extend and retract the brush.

■ The 2-in-1 brush and slot nozzle A21 can be attached directly to the

handle of the flexible hose A18 or to the telescopic tube A19.

USING THE VACUUM CLEANER

■ Pull on the power plug to wind out the required length of the power

cord and connect it to apower socket.

Attention:

The yellow mark on the power cord indicates the

approaching end of its length, and the red mark

indicates the complete end of its length. Do not

attempt to pull the power cord past this mark.

■ To start the vacuum cleaner, press button A9. When vacuuming smooth

hard floor surfaces, extend the brush on the floor nozzle A20, and

retract the brush when vacuuming carpets. The slot nozzle can be used

for vacuuming hard to reach places and the brush nozzle for vacuuming

various types of furniture.

■ Suction power can be set using the electronic control slider A4 or the

mechanical flap on the handle of the flexible hose A18.

■ When you have finished using the vacuum cleaner, turn it off by

pressing button A9 and disconnect the power cord from the power

socket. To wind the power cord back into the vacuum cleaner, press

and hold button A3 until its entire length is wound up. Gently hold the

power cord with one hand while winding it up.

Note:

If the power cord is not wound up completely, release button

A3, and pull the power cord out of the vacuum cleaner by

approximately 50 cm and then try again to wind it up.

PARKING POSITION OF THE VACUUM CLEANER

■ When not using the vacuum cleaner, you may put it in the parking

position. For the horizontal parking position, use the stopper on

the floor nozzle A20 and the groove A13, see fig. B1. For the vertical

parking position, first set the shortest length of the telescopic tube A19.

Then put the vacuum cleaner in avertical position, and slide the stopper

on the floor nozzle A20 into the groove A12, see fig. B2.

MAINTENANCE AND CLEANING

■ Before cleaning it, always make sure that the vacuum cleaner is turned

off and disconnected from the power socket.

Changing the dust bag

■ The need to replace the dust bag is signalled by the indicator A5.

■ Release the clip A7 and open the top cover of the vacuum cleaner.

Remove the used dust bag A14 from the holder A15 and insert anew

bag intended for this type of avacuum cleaner in its place. If the dust

bag is not replaced in time, the vacuum cleaner’s suction power will

be reduced.

Cleaning and replacing the inflow micro-filter and the outflow HEPA

filter

■ Release the clip A7 and open the top cover of the vacuum cleaner. Slide

the grill A16 out of the vacuum cleaner and take the micro-filter A17 out

of it. Rinse it under running lukewarm water and allow to dry naturally.

Then reinsert it and close the cover. In the event that the micro-filter A17

is showing signs of wear or it is heavily soiled, replace it with anew one.

■ Release and remove the grill A1. Remove the HEPA filter A2 from the

vacuum cleaner. In the case of light soiling, tap it out. We recommend

doing this away from living areas. In the event of greater soiling, wash

it under aweak current of running lukewarm water so that the water

washes the dirt out of the folds. Allow the HEPA filter A2 to dry naturally,

then reinsert it and secure it in place with the grill A1. It is recommended

to replace the HEPA filter with anew one after 6 months of use.

■ When filters are soiled, their effectiveness is reduced, so do not neglect

their cleaning.

Attention:

Before putting the filters back into the vacuum cleaner,

make sure that they are completely dry.

Cleaning the flexible hose, telescopic tube, floor nozzle and the

2-in-1 attachment

■ If the vacuum cleaner accessories are soiled, remove them from the

vacuum cleaner and clean all dirt off of them (dust, hair, animal fur, etc.).

Cleaning the outer surface of the vacuum cleaner

■ Clean the outer surface using adry or alightly dampened cloth. Then

wipe it thoroughly dry.

■ For cleaning the vacuum cleaner, do not use steel wool, abrasive

cleaning products, solvents etc.

■ Do not submerge the vacuum cleaner under water or any other liquid

and do not rinse it under running water.

TECHNICAL SPECIFICATIONS

Rated voltage range ...................................................................................220−240 V

Rated frequency .............................................................................................50/60 Hz

Rated power input ...............................................................................................700 W

Electrical shock protection class ...............................................................................II

Noise level ......................................................................................................... 78 dB(A)

Dust bag capacity......................................................................................................... 3l

HEPA filter efficiency class ......................................................................................E12

Length of the power cord .................................................................................... 7 m

Operational radius .................................................................................................10 m

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 6001 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SVC 6001 Manual

Product: