759481
6
Zoom out
Zoom in
Previous page
1/7
Next page
- 6 - 12/2019
Copyright © 2019, Fast ČR, a.s.
EN
Vacuum cleaner
User'smanual
Prior to using this appliance, please read the users manual thoroughly, even
in cases, when one has already familiarised themselves with previous use of
similar types of appliances. Only use the appliance in the manner described in
this user’smanual. Keep this usersmanual in asafe place where it can be easily
retrieved for future use.
■
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least
the duration of the legal liability for unsatisfactory performance or quality. In
the event of transportation, we recommend that you pack the appliance in the
original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Handle, cord winding button
A2 On/O button / electronic motor power control
A3 Outow lter protective grille
A4 Outow lter (located underneath the protective grille)
A5 Groove for the horizontal parking position
A6 On board (2 in 1 brush and crevice nozzle)
A7 Wheel
A8 Handle
A9 Hose connection hole
A10 Top cover
A11 Full dust bag indicator
A12 Flexible hose
A13 Telescopic tube
A14 Floor nozzle
A15 Upholstery nozzle
A16 2 in 1 brush and crevice nozzle
A17 Dust bag
A18 Dust bag holder
A19 Washable inow lter (located behind the removable grille)
A20 Front travel wheel
A21 Vertical parking position
BEFORE FIRST USE
Before rst use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
ASSEMBLY
Inserting the hose into the air suction hole on the vacuum cleaner.
Press both the clips on the end of the hose A12 and insert the hose end into the air
suction hole A9 on the vacuum cleaner until you hear a“click”. The hose A12 is now
secured in the correct position.
Attaching the telescopic tube:
Put the exible hose A12 on the wider part of the telescopic tube A13.
Attaching the oor nozzle to the telescopic tube:
Make sure that the oor nozzle A14 is attached to the narrower part of the telescopic
tube A13.
Adjusting the length of the telescopic tube:
Adjust the length of the telescopic tube A13 as required – disengage and hold down
the clip on the tube A13 and at the same time adjust the length of the tube A13 to
the required length. Then release the clip and slide out the tube A13 slightly forward
until you hear aclick”. The telescopic tube A13 is now securely locked in position.
USING THE VACUUM CLEANER
Connecting the vacuum cleaner to the power grid
Wind out the required length of the power cord by pulling on the power plug. Insert
the power plug into apower socket.
Attention:
The yellow marking on the power cord warns you that the
power cord is close to its end. Do not pull the cord farther than
the red marking.
Using the accessories
The oor nozzle A14 is suitable for vacuuming smooth hard oor areas and carpets.
You may set the inlet nozzle according to the oor surface by adjusting the inlet ap:
- If you want to vacuum carpets, close the bristles of the inlet inside the inlet nozzle,
by turning the ap accordingly.
- If you want to vacuum hard and smooth surfaces, extend the bristles out of the
nozzle, by turning the ap accordingly.
The crevice nozzle A16 can be used for vacuuming hard-to-reach places and the
upholstery nozzle A15 is used for gently vacuuming various types of furniture.
The 2-in-1 brush and slot nozzle A16 can be attached directly to the handle of the
exible hose A12 or to the telescopic tube A13.
Turning the vacuum cleaner on and o
To turn on the vacuum cleaner, press button A2. To turn o the vacuum cleaner, press
the button A2 again.
Adjusting the suction power
Suction power can be controlled by turning button A2, which also serves as an
electronic motor power control. Turn the button A2 clockwise towards the MAX
position to increase the power of the vacuum cleaner, turn it in the opposite direction
towards the MIN position to reduce its power. In asmaller range, you may regulate
suction power using the mechanical sliding ap on the hose handle A12.
Tips
Use maximum suction power when vacuuming carpets or hard oors.
Use alower suction power level when vacuuming upholstery, curtains,
etc.
In the event that the hose A12 becomes clogged while vacuuming,
disconnect it from the telescopic tube A13 and likewise disconnect
the hose A12 from the vacuum cleaner. Then insert the holder into
the suction hole on the vacuum cleaner and vacuum out the material
preventing the air ow.
Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for a while, you can use the horizontal A5 or
vertical A21 parking position on the vacuum cleaner, into which you insert the
stopper on the oor nozzle A14.
Attention:
Do not move the vacuum cleaner from place to place if the hose
is in the parked position! The guide tab on the oor nozzle A14
could brake o.
Ending the vacuuming process
When you nish vacuuming, switch the vacuum cleaner o by pressing button A2
and then disconnect the power cord plug from the power socket.
To wind the power cord back into the vacuum cleaner, press and hold the winding
button A1 with one hand and guide the power cord with the other.
Tip:
If the winding process stops and part of the power cord is still outside,
release the winding button A1 and pull the cable out again by about
50 cm and then press and hold the winding button A1 again and
repeat the winding process.
Carrying the vacuum cleaner
It is possible to hold and carry the vacuum by the handle A1 and A8.
CLEANING AND MAINTENANCE
Disconnect the power plug from the power socket before cleaning.
Warning:
To prevent the risk of injury by electrical shock, do not submerge
the appliance, power cord or power plug in water or any another
liquid.
Changing the dust bag
When the full dust bag indicator A11 lights up, it is necessary to replace the dust bag
A17. If you do not remove the dust bag A17, the vacuum cleaner’ssuction power
will be reduced.
1. Pull the top cover A10 upwards to open it.
2. By pulling on the collar of the dust bag, remove it from the plastic holder A18 and
insert anew bag.
3. Close the top cover A10 of the vacuum cleaner until you hear aclick.
Changing and cleaning the inow lter
1. Pull the top cover A10 upwards to open it.
2. By pulling on the collar of the dust bag, remove it from the plastic holder A18 to
make room for the removal of the lter A19.
3. Remove the protective grille and take out the lter A19.
4. In the event of lighter soiling, the lter A19 can be washed under running
lukewarm water and allowed to dry naturally. Do not dry it over aheater or using
ahair dryer. In the event of strong soiling, replace the lter A19 with anew one.
5. Put the clean and dry lter A19 back in its place secure it using the grille.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SVC 5501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SVC 5501 in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info