Under no circumstances should you attempt to process frozen food, nut
shells or hard stones that are found, for example, in mango or avocado.
2. Make sure that the food processor is correctly assembled and that the speed control knob
is set to the OFF position. Insert the power plug into an electrical power socket.
3. Place the the bowl A2 or another suitable container underneath the attachment. Use the
speed control knob to set the desired speed. We recommend to initially set the lowest
speed and then you may increase it as required.
4. Gradually add the ingredients into the feed tube B2 and push them through using the
pusher B1.
5. In the event that the attachment becomes blocked, turn off the food processor and
disconnect it from the power socket. Wait until rotating parts come to acomplete stop.
Remove the attachment and clean it out. Then assemble the attachment and reattach it
to the food processor. Connect the food processor to apower socket, turn it on and you
may continue working with it.
Attention:
When handling the grating cones B5–B9, be very careful not to injure
yourself on their sharp blades.
6. After you have finished using the appliance, set the speed control knob to the OFF position
and disconnect the power cord from the power socket.
7. Clean out the individual parts of the attachment after each use according to the instructions
in chapter Cleaning and maintenance.
CHOOSING THE RIGHT TYPE OF GRATING CONE
Food typeSlicing cone
B8–B9
Coarse
grating
cone B7
Fine grating
cone B6
Very fine
grating
cone B5
Fruit
Apples•••
Pears•••
Vegetables
Red and white cabbage•••
Carrot•••
Zucchini••
Cucumbers••
Celery•••
Onion••
Potatoes•••
Radish•••
Sweet potatoes•••
Other foods
Hard cheese
(e.g. Parmesan cheese)•••
Chocolate•••
Hard baked goods
(for breadcrumbs)•
Nuts without shells•
Note:
The provided table only recommends the suitable type of grating cone for the
given type of food. If necessary, it is possible to use your preferred grating cone
for the given type of food.
The table includes the most common types of food that can be processed. However,
you can also use the grating and slicing cone for other types of food, for which it
generally applies that it can be normally cut using aknife.
CLEANING AND MAINTENANCE
■ Before cleaning the food processor, always switch it o by setting the speed control knob
A12 to the OFF position and disconnect it from the power socket.
■ Disassemble the food processor into its individual parts. Wait until moving parts come to
acomplete stop before disassembly.
■ Thoroughly wash the used removable parts after every use using warm water with aneutral
dishwashing detergent. Then rinse them under clean running water and wipe them dry with
ane wiping cloth or allow them to dry naturally. After washing and drying, we recommend
to coat the grinding blade B6 and the grinding plates B8, B9 andB10 with cooking oil.
■ If you whisked egg whites, rst rinse the bowl A10 and the beater A4 under cold water.
If you were to use hot water, the egg white remains would harden and their removal would
be more dicult.
■ Clean the mixing container C4 by lling it with 0.5 litre of clean water and afew drops of
kitchen detergent and then assemble the blender and run it for 10 to 15 seconds. Then turn
o the food processor, disconnect it from the power socket, and after the rotating parts have
come to astop, remove the blending jar assembly. Empty out the contents of the blending
jar C4 and then thoroughly rinse out the blending jar C4 with clean water and wipe dry.
■ If more thorough cleaning is required, the cu C5 with blade assembly C6 may be removed
using aspecial wrench that can be ordered free of charge at an authorised service centre.
After cleaning, it is necessary to install the cu C5 with blade assembly C6 back in its place
and to properly tighten it using the wrench.
Attention:
When cleaning, be very careful not to injure yourself on the sharp cutting
edge.
■ After every use, it is necessary to thoroughly clean any used attachments D6–D9 in
hot water and neutral kitchen detergent. Then rinse it under clean running water and
thoroughly wipe dry with ane wiping cloth.
■ The metal parts of the meat grinder, the blade assembly C6 and attachments A3–A5
are not intended for washing in adishwasher. Other removable parts may be washed in
adishwasher.
■ For cleaning the base unit A11 and the multi-function head A7, use acloth lightly dipped
in aweak detergent solution. Then wipe everything with aclean dampened cloth and
thoroughly wipe dry.
■ For cleaning, do not use solvents or cleaning agents with abrasive eects. Otherwise, the
surface of the appliance may be damaged.
■ Do not submerge the food processor or its power cord in water or any other liquids.
STORAGE
■ When not using the food processor, store it in aclean, dry place out of children’sreach.
Make sure that the multi-function head A7 is tilted down into the horizontal position.
TECHNICAL SPECIFICATIONS
Rated voltage range ...............................................................................................................................220−240 V
Rated power input ........................................................................................................................................1 000 W
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sencor STM 6377 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sencor STM 6377 in the language / languages: English as an attachment in your email.
The manual is 1,76 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
