758521

Sencor STM 46 Manual

12
Zoom out
Zoom in
Previous page
1/22
Next page
EN-12
EN
Food Processor
STM 40WH / STM 41GR / STM 42BL / STM 43OR
STM 44RD / STM 45VT / STM 46YL / STM 47GG / STM 48RS
2014
11/2014
ASSEMBLING AND DISASSEMBLING THE SAUSAGE STUFFER ATTACHMENT
1. When assembling the sausage stuffer for fi lling sausage casings (making sausages), proceed in
the same way as when assembling the meat grinder, only with the difference that instead of the
grinding blade B6 and the grinding plate B8 or B9 only parts B0 and Bqa are used.
2. Place the separator B0 on to the screw shaft so that the notch in the grinding chamber B4 fi ts into
the groove in the separator B0. Place the sausage stuffer attachment Bqa on to the separator B0
and complete the entire sausage stuffer assembly by screwing the screw cap B7 on to the grinding
chamber B4.
3. To disassemble proceed in the reverse sequence.
USING THE SAUSAGE STUFFER ATTACHMENT
1. Make sure that the appliance is correctly assembled and that the speed control knob Aqa is set to
the OFF position. Insert the power plug into an electrical power socket.
2. Prepare a sausage casing that you will stuff with ground meat and allow it to soak in lukewarm
water for approx. 10 minutes. Place the ground meat mixture on to the hopper B2. Take the
sausage casing out of the water and skewer or tie up one end and slide the other end like a sock
on to the sausage stuffer attachment Bqa.
3. Use the speed control knob Aqa to set the desired speed. We recommend to initially set the lowest
speed and then increase it as required. With one hand hold the sausage casing on the attachment Bqa
and use the other hand to push the ground meat mixture with the pusher B1 through the feed tube
B3. If the sausage casing sticks to the attachment Bqa, it is necessary to moisten it with water again.
Attention:
Do not use fi ngers or other utensils to push the ground meat through the feed tube B3. Always
use the pusher B1 designed for this purpose.
4. To turn off the appliance, set the speed control knob Aqa to the OFF position.
5. Clean out the individual parts of the attachment after each use according to the instructions in
chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE KEBAB MAKER ATTACHMENT
1. When assembling the kebab maker attachment, proceed in the same way as when assembling the
meat grinder, only with the difference that instead of the grinding blade B6 and the grinding
plate B8 or B9 only parts Bqs a Bqd are used.
2. Place the moulder Bqs on to the screw shaft so that the notch in the grinding chamber B4 fi ts
into the groove in the moulder Bqs. Place the kebab moulder attachment Bqs on to the conical
attachment Bqd and complete the entire kebab maker assembly by screwing the screw cap B7 on
to the grinding chamber B4.
3. To disassemble proceed in the reverse sequence.
USING THE KEBAB MAKER ATTACHMENT
1. Make sure that the appliance is correctly assembled and that the speed control knob Aqa is set to
the OFF position. Insert the power plug into an electrical power socket.
2. Place the ground kebab meat mixture on to the hopper B2. Use the speed control knob Aqa to
set the desired speed. We recommend to initially set lower speed and then increase it as required.
Using the pusher B1, push the mixture through the feed tube B3. The result will be a hollow meat
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor STM 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor STM 46 in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info