758544

Sencor STM 3622 Manual

14
Zoom out
Zoom in
Previous page
1/16
Next page
EN-14
EN
Food Mixer
STM 3620WH, STM 3621GR, STM 3622BL, STM 3623OR, STM 3624RD
STM 3625VT, STM 3626YL, STM 3627TQ, STM 3628RS
2015
07/2015
• Set the speed to 2 and gradually add the flour until everything is properly combined into a single
mass. Do not, however, beat for too long.
• Use a teaspoon to form small balls and lay them out evenly on to a lightly greased or parchment
paper covered baking tray. Leave sufficient room around each ball. Using a lightly floured fork,
push down each of the balls.
• Bake in a preheated oven at 190 °C for approximately 12–15 minutes or until the biscuits are lightly
golden in colour.
• Take the biscuits off the baking tray and leave to cool down on a metal rack.
Cream snow puffs (20–24 pcs)
4 egg whites
1 cup of caster sugar
• Use the whisk A2.
• Set the speed level to 6 and whip up a thick snow from the egg whites. Lower the speed to level 1
and carefully add half the sugar and whip it in. Then add the remaining sugar.
• Using a spoon, apply a small amount of the snowy mixture on to a lightly greased baking tray.
Leave about 3 cm around the individual pieces so that they do not bake to one another.
• Bake in the oven at 120 °C about 1 to 1½ hours or until the snow puffs are dry. To avoid burning
them, do not, however, bake then too long. Take them off the baking tray and put them aside to
cool down and store them in an air-tight container.
Note:
You can use a decorating tool to create larger snow puffs. This may necessitate a longer baking
time.
White bread
4 cups (600 g) of bread flour
3 tablespoons of dried milk
1½ teaspoons of salt
1½ tablespoons of sugar
1 teaspoon of bread improver
2 teaspoons of instant yeast
2 tablespoons of oil
1½ cups (375 ml) of water
additional bread flour for hand kneading
• Use the kneading hook A1.
• In the mixing bowl, mix the flour, dried milk, salt, sugar, bread improver and the instant yeast.
• Set the speed to 1–2 and slowly add water and oil into the dry mix. Leave it to knead until a dough
starts to form.
• Move the dough on to a lightly floured rolling board and thoroughly knead by hand until the
dough is sufficiently fine and smooth.
Note:
At this stage, the dough should be very well kneaded so that gluten is formed, which gives the
dough the correct elasticity and helps it to rise.
• Place the dough into a large bowl and cover with plastic wrap. Allow it to rise in a warm place for
about 20 minutes or until the dough doubles in size.
… 14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor STM 3622 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor STM 3622 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info