Manual Sencor SSV 330 (page 6 of 7) (English)

758413

Zoom out

Zoom in

1/7

06/2017

- 6 -

EN Electric Spiralizer

User'smanual

■Prior to using this appliance, please read the user’s manual

thoroughly, even if you already have experience in using similar

appliances. Only use the appliance in the manner described in this

user’smanual. Keep this user’smanual in asafe place where it can be

easily retrieved for future use.

■We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the

vendor or warranty card for at least the duration of the legal

liability for unsatisfactory performance or quality. In the event of

transportation, we recommend that you pack the appliance in the

original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE AND ACCESSORIES

A1 Drive unit

A2 Food holder

A3 Feed tube

A4 Wide spiral cutting blade

A5 Thin strip cutting blade

A6 Narrow spiral cutting blade

A7 Lid cover

A8 Pulse switch for turning the

drive unit on and o

A9 Jug lid

A10 2.7-litre transparent jug

A11 Anti-slip feet

BEFORE FIRST USE

1. Take the appliance and its accessories out of the packaging

materials.

2. Except for the drive unit A1, thoroughly wash all the individual

parts of the blending jar using warm water and a neutral kitchen

detergent. Then rinse under clean water and allow them to dry

naturally or dry them. Do not submerge the drive unit A1 in water

or rinse it under running water.

Attention:

Be especially careful when cleaning the blades A4–A6 to

avoid injury on the sharp edges.

ASSEMBLING AND DISASSEMBLING THE APPLIANCE

■Before you start assembling or disassembling the appliance, check

that it is turned o and disconnected from the power socket.

■Place the jug A10 on an even, dry and stable surface. Place the lid

A9 on to the jug A10 and push it down along its entire perimeter.

■Insert one of the cutting blades A4–A6 from above into the hole

in the lid A9 so that it slides in along its entire perimeter. Turn

the blade clockwise all the way to lock in the latches along the

perimeter of the blade.

Attention:

When inserting the cutting blade A4–A6 into the lid A9, take

care not to injure yourself on its sharp edge.

■Place the feed tube A3 on to the lid A9 and turn it clockwise all the

way to lock in the latches along the perimeter.

■From underneath, put the food holder A2 on to the shaft of the

drive unit A1. The appliance is now assembled and ready for use.

■The lid A9 with cover A7 serves to cover the jug A10 when you wish

to use it to store the processed food in it for ashort time. Place the

lid A9 on to the jug A10 and into the hole in the lid A9 insert the

cover A7 and turn it clockwise all the way until it locks into place.

■Disassemble the appliance in the reverse sequence.

OPERATING THE APPLIANCE

1. This appliance is suitable for processing harder types of fruits

and vegetables such as, for example, potatoes, sweet potatoes,

celery, beetroot, radish, pumpkin, cucumber etc. in the raw form.

It is not particularly suitable for processing soft types of fruits and

vegetables.

2. Thoroughly wash all the fruit and vegetables and remove the stones

and kernels. Cut them up so that they are not longer than the height

of the feed tube A3, so that their diameter is not greater than 7 cm

and so that both ends are at.

Attention:

Never attempt to use this appliance to process hard stones

contained in, for example, mangoes,etc.

3. Make sure that the correct type of blade is installed in the appliance

and that the appliance is correctly assembled. Place the jug A10 on

an even, dry and stable surface.

4. Make sure that the drive unit A1 is disconnected from the mains

power socket. Stick the prepared piece of fruit or vegetable on to

the food holder A2.

5. Grasp the drive unit A1 in one hand and with the end on which the

food is located slide it into the opening in the feed tube A3 in such

away that the guide tabs on the drive unit A1 are aligned with the

guide tabs inside the feed tube A3, see g. B.

6. Insert the drive unit’sA1 power plug into apower socket. Press the

pulse switch A8 and start pushing the food through the cutting

blade.

Attention:

The maximum continuous operating time of the appliance

is 1 minute. Before turning it on again, allow it to cool down

for at least 3 minutes. After ve consecutive cycles, allow the

appliance to cool down for 20 minutes.

7. Once the food is cut up, release the switch A8. This will turn o the

appliance. Wait until rotating parts come to a complete stop and

disconnect the drive unit A1 from the power socket. Usually, apiece

of the food remains on the holder A2 and it needs to be removed.

Before putting more food into the holder A2 make sure that the

appliance is disconnected from the power socket.

8. In the event that the jug A10 lls up during operation, turn o

the appliance, disconnect it from the power socket and make sure

that the rotating parts have stopped. Empty out the jug A10 and

reassemble the appliance. After it has cooled down, you may use it

again.

9. When you have nished using it, disconnect the appliance from

the power socket and clean it out according to the instructions

contained in the chapter Cleaning and maintenance.

CLEANING AND MAINTENANCE

■Wash the appliance after every use. Before cleaning it, make sure

that the appliance is turned o and disconnected from the power

socket and that the rotating parts have stopped.

■Disassemble the appliance into its individual parts. Except for the

drive unit A1, thoroughly wash all the used parts under running

warm water using a neutral kitchen detergent. Then rinse them

under clean running water and wipe dry. Certain types of food

such as beetroot, may cause discolouration of plastic parts of the

appliance. If this occurs, coat them with cooking oil and then clean

them out in the normal way. Discolouration does not have any

eect on the functionality of the appliance.

Attention:

Be especially careful when cleaning the cutting blades A4–A6

to avoid injury on the sharp edges.

■For cleaning the drive unit A1, use acloth lightly dipped in aweak

solution of water and neutral kitchen detergent. Then thoroughly

wipe everything with aclean dampened cloth and wipe dry. Never

submerge the drive unit A1 or its power cord in water or any other

liquids.

■For cleaning, do not use solvents, abrasive cleaning products, etc.

Otherwise the surface may be damaged.

TECHNICAL SPECIFICATIONS

Rated voltage range ............................................................................220−240 V

Rated frequency ......................................................................................50/60 Hz

Rated power input ....................................................................................... 100 W

Electrical shock protection class ........................................................................II

Noise level .................................................................................................. 80 dB(A)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SSV 330 in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sencor SSV 330

Sencor SSV 330 User Manual - Dutch - 7 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SSV 330 Manual

Product: