758810

Sencor SSJ 4043 Manual

7
Zoom out
Zoom in
Previous page
1/10
Next page
Masticating Slow Juicer
SSJ 4041BK / SSJ 4042RD / SSJ 4043WH
EN
EN-7
2015
04/2015
USING THE JUICER
1. Make sure that the juicer is correctly assembled and then connect it to the el. power socket. The
juicer is equipped with a safety mechanism that prevents it from being started unless the lid is
correctly secured in the correct position.
2. Place the juice jug A8, a glass or another suitable container below the juice spout A7. Open the
lock of the juice spout A7 so that the juiced juice can flow freely out of the juice collector A6.
Place the pulp container A0 below the pulp outlet A9.
3. Prepare the fruit or vegetables. Thoroughly wash the ingredients and cut them up into pieces
that will pass through the feed tube A2. Remove hard stones that are contained in, for example,
apricots, peaches, mangoes, etc. and inedible peels, e.g. from oranges, pineapples, melons,
mandarins, etc.
4. Prior to starting the juicer, make sure that the lid is properly secured in the correct position. To
turn on the juicer, turn the control dial Aqa to the ON position. Take the pusher A1 out of the
feed tube A2 hole. Gradually add the prepared ingredients into the feed tube A2 and push them
down using the pusher A1. You will achieve optimal results if you fill the feed tube A2 gradually
pushing the ingredients down gently.
Attention:
Do not use fingers or other utensils to push ingredients through the feed tube A2. Always use
the pusher A1 designed for this purpose.
The maximum time of non-stop operation of this appliance is 15 minutes. Then allow it to cool
down for 10 minutes.
5. If the juice jug A8 or pulp container A0 fill up during the juicing process, turn the juicer off by
turning the control dial Aqa to the OFF position, empty out the respective container and then put
it back in its place. Then you can put the juicer back into operation and continue juicing.
6. When you have finished juicing, we recommend that you remove pulp remains from the juice
collector A6. Hold the control dial Aqa in the "R" position (reverse motor rotation) for 3–5 seconds,
and then release it so that it returns to the OFF position. Repeat the entire process two to three
times. You can do the same in the event that you clog up the appliance with an excessive amount
of ingredients.
7. Turn the juicer off by setting the control dial Aqa to the OFF position and disconnect it from the
power socket. Prior to removing the juice jug A8, we recommended closing the spout A7 so that
juice does not drip out of it.
8. Disassemble the juicer, see chapter Disassembling the juicer and clean it out according to the
instructions contained in chapter Cleaning and maintenance.
DISASSEMBLING THE JUICER
1. Before disassembling the juicer, make sure that it is turned off and disconnected from the power
socket. Make sure that all parts that move during operation have stopped moving.
2. Close the juice spout A7 and remove the juice jug A8 and the pulp container A0. Take the pusher
A1 out of the feed tube A2.
3. Turn the feed tube A2 anticlockwise until the open lock symbol shown on the lid A2 is aligned
with the " " symbol on the juice collector A6 and then take it off the juice collector A6.
4. Remove the juice collector A6 with the holder A5, strainer A4 and auger A3 inside off the base
Aqs by turning it anticlockwise and lifting it up.
Note:
It will be easier to take the juice collector A6 off the base Aqs when the pulp remains are cleaned
out after juicing, as described in point 6 in chapter Using the juicer.
5. Take the auger A3, strainer A4 and holder A5 out of the juice collector A6.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SSJ 4043 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SSJ 4043 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info