Manual Sencor SRV 2230 (page 8 of 11) (English)

759460

Zoom out

Zoom in

1/11

EN Robotic vacuum cleaner

User'smanual

BEFORE FIRST USE

■ Prior to using this appliance, please read the user‘smanual thoroughly, even in cases,

when one has already familiarised themselves with previous use of similar types of

appliances. Only use the appliance in the manner described in this user’smanual.

Keep this user‘smanual in asafe place where it can be easily retrieved for future use.

In the event that you hand this appliance over to somebody else, make sure to also

include this user‘smanual.

■ We recommend saving the original cardboard box, packaging material, purchase

receipt and responsibility statement of the vendor or warranty card for at least the

duration of the legal liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance in the original box

from the manufacturer.

■ Carefully unpack the appliance and take care not to throw away any part of the

packaging before you find all the parts of the appliance.

DESCRIPTION OF THE APPLIANCE AND ACCESSORIES

A1 Bumper bar with an anti-collision

sensor

A2 Start button for automatic clean /

indicator light

A3 Lid

A4 Main switch

A5 Power adapter connector socket

A6 Latch

A7 Dust container compartment

A8 Exhaust hole

A9 Lid latch hole

A10 Dust container cleaning brush

A11 Dust container

A12 HEPA filter (highly effective air-

borne particle filter able to capture

even the finest dust particles)

A13 HEPA filter holder

A14 Dust container lid

A15 Bottom anti-fall sensor, central

A16 Charging contacts

A17 Left rotary brush (L)

A18 Bottom anti-fall sensor, left

A19 Left motorised rubber wheel

A20 Battery compartment cover

A21 Central rotary brush

A22 Suction hole (underneath the rotary

brush cover)

A23 Right rotary brush (R)

A24 Front swivel wheel

A25 Bottom anti-fall sensor, right

A26 Right motorised rubber wheel

A27 Latches for attaching the water tank

with mop

B1 Power adapter

B2 Power adapter plug

B3 Charging station

B4 Power adapter plug socket

B5 Charging contacts

C1 Battery compartment

C2 Battery insertion tube

C3 Robotic vacuum cleaner connector

C4 Battery connector

C5 Insulation tape for easier battery

removal

C6 Battery

D1 Water tank

D2 Water tank release latch (on both

sides)

D3 Filling opening cap

D4 Duster

D5 Duster fastening velcro strips

E1 Remote control

E2 Display

E3 Scheduled cleaning setting mode

E4 Return to the charging station

button

E5 Forward button

E6 Left button

E7 Right button

E8 Reverse button

E9 Vacuum cleaner start / off button

E10 Cleaning mode selection button

E11 Time setting button

E12 Maximum cleaning mode in which

the vacuum cleaner cleans

until the battery is almost flat.

E13 Battery compartment cover

E14 Battery compartment (2pcs AAA x

1.5V)

F1 Latches

F2 Rotary brush cover

F3 Rotary brush

PURPOSE OF USE AND FEATURES OF THE ROBOTIC VACUUM

CLEANER

■ The robotic vacuum cleaner is intended for cleaning various types of hard floors

such as wooden or laminate floating floors, tiles, vinyl, etc. and carpets with alow

pile height. While vacuuming, it effectively combines various routes to optimally

clean the entire floor area.

■ The suction hole effectively removes hair, animal fur, etc. The two side rotary brushes

brush dirt out of hard-to-reach places along walls and furniture and out of corners.

The motorised rubber wheels protect sensitive floors against scratching and can

travel over threshold strips up to aheight of 1 cm and ride on to a2 cm high carpet.

■ The suspended bumper enables the vacuum cleaner to dampen the approach to an

obstacle and to efficiently clean around it. The infrared sensors in the front bumper

prevent the robotic vacuum cleaner from colliding with obstacles. Safe operation in

rooms with stairs is made possible by the bottom anti-stair-fall sensors.

■ Another advantage the a robotic vacuum cleaner is the mop function, which

enables dry and wet wiping of smooth hard floor surfaces. While wiping, the robotic

vacuum cleaner vacuums small bits of dirt and dust from the floor to prevent the

duster from being excessively soiled during the cleaning cycle.

■ For easy identification of the operating state, the button on the top cover has an

indicator light the colour of which indicates low battery voltage (lit red), battery

charging (flashing red), full charge and operation (lit blue). Error states are then

indicated by various numbers of flashes or colour combinations, see chapter

TROUBLESHOOTING. Apart from the indicator lights, the vacuum cleaner also

has audio signals that accompany certain functions or error states of the vacuum

cleaner, see chapter AUDIO SIGNALS.

PREPARING THE ROBOTIC VACUUM CLEANER FOR OPERATION

INSTALLING AND USING THE ROTARY BRUSHES

■ The rotary brushes A17 and A23 are intended for smooth floor surfaces and ensure

effective cleaning in corners, along walls and furniture.

■ Turn the vacuum cleaner upside down. Gradually push the rotary brushes precisely

and with force on to the pins that are intended for them. While doing this, make sure

that the marks L and R both on the brushes and on the vacuum cleaner match. Turn

the robotic vacuum cleaner back over to the operating position.

■ When using the vacuum cleaner to clean rooms with carpets, remove the rotary

brushes. When removing them, proceed in the reverse sequence to their installation.

INSERTING AND REMOVING THE BATTERY

■ The robotic vacuum cleaner is equipped with aLi-ion battery C6. If the battery is

packed separately, it is necessary insert it into the vacuum cleaner before first use.

Use only the original battery type.

■ Make sure that the vacuum cleaner is turned off with the main switch A4. Turn the

vacuum cleaner upside down and screw off the cover A20.

■ Remove the connector C3 from the battery compartment C1.

■ Slide the battery into the tube C2 and connect the battery connector C4 to vacuum

cleaner connector C3.

■ Screw the cover A20 back on and turn the vacuum cleaner back over to the

operating position.

■ Remove the battery in reverse sequence. Prior to removing the battery, always check

that the vacuum cleaner is turned off using the main switch A4. To make removal

easier, use the two insulating strips C5.

■ When the vacuum cleaner will not be used for an extended period of time, take out

the battery and store it in adry, clean and cool place out of children‘sreach.

LOCATION OF THE CHARGING STATION

■ The charging station B3 serves to automatically recharge the battery and the

vacuum cleaner must have good access to it.

■ Locate the charging station against awall on ahard, even and dry surface within

reach of a power socket. Make sure that there are no stairs or obstacles within

adistance of 1m on the left and right of the charging station and within adistance

of 2 m in front of the charging station, that would prevent the robotic vacuum

cleaner from finding the charging station and docking successfully.

■ Insert the power adapter plug B2 into socket B4 of the charging station, and insert

the power cord plug into apower socket. Place the power cord in such away that it

does not tangle into the cleaning brushes of the robotic vacuum cleaner.

■ In the event that the vacuum cleaner is not used for an extended period of time,

disconnect the charging station from the power socket and store it in adry, clean

and cool place.

CHARGING THE BATTERY FOR THE FIRST TIME

Note:

Prior to charging the battery, the vacuum cleaner must be turned on

using the main switch A4.

■ Before using the vacuum cleaner for the first time, it is necessary to fully charge the

battery for at least 7 hours. Thereafter, astandard charge will take approximately

4 hours.

■ Check that the charging station B3 is correctly positioned and connected to apower

socket according to chapter Location of the charging station. Turn on the main

switch A4 of the vacuum cleaner, grasp the robotic vacuum cleaner and manually

place it into the charging station so that the charging contacts A16 on the underside

of the vacuum cleaner and the charging contacts B5 on the charging station are

connected. When the contacts are connected, the charging process will start.

■ The vacuum cleaner can also be charged without using the charging station. Insert

the plug B2 of the power adapter B1 into socket A5 of the vacuum cleaner, and

insert the power cord plug into apower socket.

■ During the charging process, the indicator light on button A2 will flash red.

■ When the battery is fully charged, the indicator light of switch A2 will remain

permanently lit blue and the process will end automatically. The vacuum cleaner

is now ready for use.

INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL

■ Push down the latch of cover E13 on the rear side of the remote control E1 to release

it and remove the cover.

■ Insert two type AAA (1.5 V) batteries into the remote control. When inserting the

batteries, ensure the correct polarity as shown inside the battery compartment E14.

Put the cover E13 back on and click it into place.

■ In the event that the batteries are flat, replace them with new ones. Do not combine

various types of batteries or new and old batteries.

■ The signal range of the remote control is approximately 6 m.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SRV 2230 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SRV 2230 Manual

Product: