757129
2
Zoom out
Zoom in
Previous page
1/3
Next page
Important:
·
··
·
In order for other people to receive your transmission, they must
also be on the same channel that you are currently using. Refer
to the "Changing Channel" section for more information.
·
··
·When the PTT and/or CALL buttons are continuously pressed,
your PMR cannot receive any transmissions.
3.5 Roger Beep
The Roger Beep is a tone which is automatically transmitted
whenever the PTT button is released. This alerts the
receiving party that you have ended the transmission, and
you are now in receive mode.
3.6 Changing Channels
The PMR has 8 available channels. To change channels, in
normal mode;
a. Press the (Menu) button, the channel icon “1 ” on the LCD
screen will start blinking.
b. While the Channel icon is blinking, press the or
button to select the desired channel. The
channel changes from 1 to 8, or vice versa.
c. Press the (Menu) button to confirm your setting and return
to the standby mode.
Note:
Refer to the :Channel Table” section of this Owners Manual for
detailed frequency listing.
Battery meter
The battery icon is located in the left corner of the LCD panel. This battery icon
will displayed when low battery status. These indicate that the battery level
reaches its minimum level, at this stage the handset will emit two beep tones and
then it will automatically turn Off the power.
Battery life
The PMR has a built in power saver feature to make the batteries
last longer. But when you are not using the handset, it's better to
switch off to save the battery power.
3. Operation
3.1 Turning the Unit ON/OFF
To Turn ON;
a. Press and hold the (Power) button. A special “beep" sound
will be heard. The LCD screen will display the current channel.
To switch OFF;
b. Press and hold the (Power) button. A special “beep" sound
will be heard and the LCD screen will turn blank.
3.2 Adjusting the speaker volume
There are 8 volume levels, the current speaker volume level
is displayed on the LCD screen.
To adjust the speaker volume level, press the (UP) button to
increase, or press (DOWN) button to decrease. The LCD screen
will display the speaker volume icon bars ascending, or descending
respectively.
3.3 Receiving a Call
The unit is continuously in receive mode when the unit is turned
ON and not transmitting. When a signal is received on the current channel, 3.7 Calling (Paging) Tone
the receive signal iconRX” will be displayed on the LCD screen. You can use the CALL button to send a tone to other users on
the same channel. To activate this feature;
3.4 Transmitting (sending) a. With the PMR in normal mode, press and release the
button. The unit will transmit a 2-second page tone to the other
a. Press and hold the PTT (Push to Talk) button to transmit your voice. unit/s set with the same channel within transmitting range.
The transmit signal icon “TX” will display on the LCD screen.
b. Hold the unit in a vertical position with the Mic (Microphone) 5 cm
away from the mouth. While holding the PTT button, speak into the
microphone in a normal tone of voice.
c. Release the PTT button when you have finished transmitting.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SMR 130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SMR 130 in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info