Manual Sencor SJE 5050 (page 6 of 7) (English)

758820

Zoom out

Zoom in

1/7

02/2017

EN Juicer

User’smanual

Prior to using this appliance, please read the user'smanual thoroughly, even in cases

where you have previously familiarised yourself with the operation of similar types

of appliances. Only use the appliance in the manner described in this user'smanual.

Keep this user'smanual in asafe place where it can be easily retrieved for future

reference.

We recommend saving the original cardboard box, packaging material, purchase

receipt and responsibility statement of the vendor and warranty card for at least the

duration of the legal liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance in the original box

from the manufacturer.

DESCRIPTION OF THE JUICER

A1 Pusher

A2 Feed tube

A3 Lid

A4 Titanium strainer

A5 Juice collector

A6 Locking arm

A7 Base unit

A8 0/Iswitch

A9 LCD speed indicator

A10 Control button

A11 Juice jug

A12 Spout with DripStop technology

A12a, which serves to prevent

dripping after extraction

A13 Pulp container

LCD SPEED INDICATOR

Level 1 – SOFT FRUIT: soft fruit

Level 2 – CITRUS: citrus fruits

Level 3 – PINEAPPLE: pineapple and fruits of similar hardness

Level 4 – APPLE: apples

Level 5 – HARD VEG: harder vegetables

BEFORE FIRST USE

1. Remove all packaging materials from the appliance and its accessories.

2. Thoroughly wash all removable parts (pusher A1, lid A3, titanium strainer A4,

juice collector A5, the juice jug A11 and pulp container A13) that come into

contact with food in warm water using kitchen detergent. Then rinse all these

parts under clean running water and thoroughly wipe dry with a ne wiping

cloth.

3. The pusher A1, titanium strainer A4 and the pulp container A13 may be washed

in adishwasher. We recommend washing the titanium strainer A4 in the top rack

of the dishwasher.

Attention:

The blade at the bottom of the titanium strainer A4 is very sharp and so

it is necessary to be especially careful when handling it. Careless handling

may lead to injury.

ASSEMBLING THE JUICER

1. Place the juicer on an even, dry surface, e.g. on awork table. Prior to assembly,

always check that the juicer is turned o (switch 0/IA8 is in position 0 – turned

o) and the power cord is disconnected from the power source.

2. Insert the juice collector A5 into the juicer – base unit A7 as shown in the picture.

Make sure that the juice collector spout A12 is located in the groove in the base

unit. Place the DripStop A12a on to the spout A12.

3. Insert the titanium strainer A4 into the juice collector A5. Make sure that the

strainer is properly seated on the drive shaft.

4. Tilt the pulp container A13 with its upper edge towards the base unit A7 and

slide it from underneath on to the rim of the juice collector. Then push the

bottom of the pulp container towards the base unit. When correctly seated,

there should be aspace of no more than 1 mm between the pulp container A13

and the base unit.

5. Cover everything with the lid A3 and push it down into the correct position.

6. Use one hand to push the lid A3 downwards and at the same time tilt the locking

arm A6 on to it so that the lid is secured in the correct position. An audible click

will be heard. The juicer is equipped with asafety mechanism that prevents it

from being started unless the lid is correctly seated and secured in place with

the locking arm.

7. Place the juice jug A11 underneath the spout A12.

8. Insert the pusher A1 into the feed tube A2 hole. Notice, that to make movement

easier, the pusher A1 has grooves that slide over the tabs in the top part of the

feed tube A2.

9. The juicer is now assembled and ready for use.

USING THE JUICER

1. Make sure that the juicer is correctly assembled and then connect it to the el.

power socket. The juicer is equipped with asafety mechanism that prevents it

from being started unless it is correctly assembled.

2. Place the juice jug A11, aglass or another suitable container below the juice

spout A12. Check that the pulp container A6 is installed in its place. Check

the DripStop A12a, it should be turned to the right to enable the juice to ow

through from underneath.

3. Prepare ingredients suitable for juicing (fruit and vegetables). Thoroughly

wash them and cut them up into pieces that will pass through the feed tube

A2. Remove hard stones that are contained in, for example, apricots, peaches,

mangoes, etc. and inedible peels, e.g. from oranges, pineapples, melons,

mandarins, etc.

4. Prior to starting the juicer, make sure that the lid A3 is properly secured in the

correct position. Using the control button A10, set the required level depending

on the hardness of the ingredients. The juicer can be set from the lowest level 1

(which is intended for soft ingredients, e.g. bilberries, water melon, tomatoes) to

the highest level 5 (which is intended for hard ingredients, e.g. celery, beetroot,

etc.).

5. Turn on the juicer (set the 0/Iswitch A8 to position I– on). The level 1–5 can be

set during the juicing process depending on the hardness of the ingredients.

Take the pusher A1 out of the feed tube A2. Gradually add the prepared

ingredients into the feed tube A2 and push them down using the pusher. You

will achieve optimal results if you ll the feed tube A2 gradually and push the

ingredients down gently.

Attention:

Do not use ngers or other utensils to push ingredients through the feed

tube A2. Always use the pusher A1 designed for this purpose.

The maximum time of non-stop operation of this appliance is 15 minutes.

Then allow it to cool down for 10 minutes.

When juicing larger batches of ingredients, do not run the appliance non-

stop for longer than 10 seconds.

6. If the juice jug A11 or pulp container A13 ll up during the juicing process,

turn the juicer o by setting the 0/Iswitch A8 to position 0 – o, empty out the

respective container and then put it back in its place. Then you can put the juicer

back into operation and continue juicing.

7. To turn o the juicer, set the 0/Iswitch A8 to position 0 – o. Then disconnect the

juicer from the power socket. Allow the juice to ow out, then turn the DripStop

A12a to the left to prevent dripping.

8. When you have nished using the juicer, disassemble it according to the

instructions contained in chapter Disassembling the juicer and clean it out

according to the instructions contained in chapter Cleaning and maintenance.

Before disassembling the juicer, make sure that the juicer is turned o (0/Iswitch

A8 is in position 0 – o), disconnected from the power socket and that the

rotating parts have stopped.

USEFUL ADVICE AND TIPS

■ Before you start juicing, thoroughly wash all the ingredients and cut them up

into smaller pieces that will pass through the feed tube A2. Remove hard stones

that are contained in, for example, apricots, peaches, mangoes, etc. and inedible

peels, e.g. from oranges, pineapples, melons, mandarins, etc.

■ To achieve optimal results, always process only fresh ripened fruits and

vegetables. Overripe or unripe fruits and vegetables will negatively aect the

resulting taste of the juice.

■ If you juice fruits and vegetables of varying consistency, we recommend that

you start with the softer fruits and vegetables, e.g. citruses, berries, etc. and then

proceed on with harder fruits, e.g. apples. Always select aspeed appropriate for

the type of ingredients that are being juiced.

■ Do not use the juicer for processing frozen or excessively hard ingredients, e.g.

sugar cane.

■ Place the ingredients into the feed tube A2 gradually and push through gently

with mild pressure. Do not overll the feed tube A2 and do not push the

ingredients in too quickly and with excessive pressure. The process separating

the juice from the pulp occurs gradually and will not be sped up by pushing

ingredients in quickly.

■ To prevent freshly pressed apple juice from turning brown, you can add alittle

lemon juice.

■ To prevent losing valuable minerals, we recommended consuming the juice

immediately after it is pressed.

DISASSEMBLING THE JUICER

1. Check that you have turned o the juicer by setting the 0/I switch A8 to

position 0 – o and disconnected the power cord from the power source. Wait

until rotating parts come to acomplete stop before disassembly. Wait until the

juice ows out and turn the DripStop A12a to the left to prevent the juice from

dripping.

2. Release the locking arm A6 from the lid and tilt it downwards.

3. Remove the lid A3 and take out the pulp container A13 by tilting the bottom

away from the base unit. Then slide the pulp container from underneath the rim

of the juice collector A5.

4. Take out the juice collector A5 with the titanium strainer A4 still inside it by

pulling it upwards away from the base unit A7.

5. Take the titanium strainer A4 out of the juice collector A5. We recommend that

the strainer A4 is removed over akitchen sink.

Attention:

There is ablade in the middle part of the strainer A4. Be especially careful

to avoid injury when handling the strainer A4. Do not touch the blade.

CLEANING AND MAINTENANCE

■ Make sure that the juicer is turned o (the 0/Iswitch is in position 0 – o), the

power cord is disconnected from the power source and that rotating parts have

stopped.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SJE 5050 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sencor SJE 5050

Sencor SJE 5050 User Manual - Dutch - 7 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SJE 5050 Manual

Product: