Manual Sencor SHP 8400 (page 9 of 9) (English)

759970

Zoom out

Zoom in

1/9

08/2018

- 9 -

■ Because hair grows in various directions, it is also necessary to move the hair clipper

in various directions (upwards, downwards or crosswise).

■ Repeat individual passes so that you cut also the hair that you did not cut in the

previous passes.

■ Ensure that the flat part of the comb attachment is in full contact with the scalp. This

will ensure an even haircut result.

■ To achieve good results on curly, sparse or long hair, you can try using acomb to lead

the hair towards the hair clipper.

■ Trim beards by slowly moving counter to the growth direction of the beard, going

from the bottom upwards. When trimming beards using acomb attachment, keep in

mind that the selected comb attachment must be in constant contact with the skin

in order to ensure an even cut. After reattaching the attachment on to the cutting

unit A2, do not forget to set the cutting height again.

■ Regularly clean away hair and whiskers from the cutting unit. In the event that

alarge amount of hair or whiskers accumulates in the cutting blade, take it off the

hair clipper and blow or tap the hair or whiskers out of it.

CLEANING AND MAINTENANCE

■ Regular cleaning of the hair clipper after every use will ensure its proper operation.

■ Before you start cleaning the hair clipper, turn it off and disconnect it from the power

socket.

Attention:

This hair clipper is not designed to be washed under awater tap. Do

not spray the hair clipper or its power adapter A8 with water or any

other liquid or submerge it in water or any other liquid.

CLEANING THE CUTTING UNIT

■ Remove the comb attachment from the cutting unit A2 when it is ready.

■ Use the cleaning brush B9 to remove all hair, whiskers or body hair from the cutting

unit A2 and all the remaining attachments B1 to B8.

■ Remove the cutting unit A2 from the hair clipper, see figure E. Hold the hair clipper in

one hand so that your thumb is positioned on the underside of the cutting unit A2.

Use the thumb of the other hand to push the cutting unit from the handle A6 until

the cutting unit A1 is fully released.

Attention:

The edge of the cutting blade A1 is sharp, pay increased

attention when handling it.

■ Use the brush B9 to remove all hair or whiskers from the cutting unit A2 and from

the inner area of the hair clipper underneath the cutting unit A2.

■ After cleaning, reattach the cutting unit A2 to the handle of the hair clipper A6, see

figure F. Slide the tab on the underside of the cutting unit A2 into the cut-out in

the handle of the hair clipper A6 and then push the cutting unit A2 against the hair

clipper until an audible click is heard.

CLEANING THE COMB ATTACHMENTS

■ Comb attachments B1 toB8 can be washed under lukewarm running water. After

washing an attachment, carefully wipe it with asoft, dry cloth and then allow it to

dry naturally.

■ The hair clipper handle A6 can be cleaned using aclean dry cloth. In the event that

it is very dirty, you can use a lightly dampened cloth. Then thoroughly wipe the

cleaned surface dry.

■ To clean the power adapter A8, use aclean, dry cloth.

■ For cleaning, do not use brushes with hard bristles, cleaning products with an

abrasive effect, solvents, etc. Otherwise, the cleaned surface may be damaged.

LUBRICATING THE BLADE OF THE CUTTING UNIT

■ To ensure complete movement of the cutting unit blades A1, we recommend that it

is regularly lubricated always after several sessions.

■ If acomb attachment is mounted on the cutting unit A2, remove it.

■ Apply 1 to 2 drops of oil B10 to the blade of the cutting unit A1 and evenly spread

the oil using acloth. Dry off excess oil. Check that the cutting blade is clean before

using again.

Note:

After using up the supplied oil B10 you can use an oil that does not

contain acids, e.g. sewing machine oil.

STORAGE

■ When you have finished using it, you may store the hair clipper with all its accessories

in the supplied case B11. Keep the case with the hair clipper away from extreme

temperatures, direct sunlight and excessive humidity and do not store it in an overly

dusty environment.

TECHNICAL SPECIFICATIONS

Hair clipper

Built-in battery...............................................................................................Li-ion, 3.6 V, 2200 mAh

Output ............................................................................................................................................ 5 V, 1 A

Dimensions (width × depth × height) .......................................................... 174 × 52 × 32 mm

Weight ............................................................................................................................................... 120g

Noise level ...................................................................................................................................72 dB(A)

Power adapter

Rated voltage range .................................................................................................... 100−240 VAC

Rated frequency.......................................................................................................................50–60 Hz

Output ......................................................................................................................... 5 V/DC, 1,000 mA

Length of the power cord.........................................................................................................195 cm

The declared noise emission level of the appliance is 72 dB(A), which represents alevel

Aof acoustic power with respect to areference acoustic power of 1 pW.

EXPLANATION OF TECHNICAL TERMINOLOGY

Safety class for electrical shock protection:

IP20 – The appliance is constructed in such a way that it is not possible for any

dangerous live parts of the appliance to come into contact with the human body and

at the same time the appliance is protected against the damaging effects of water that

could enter into the appliance.

Changes to text and technical parameters are reserved.

DISPOSAL OF USED BATTERIES

Prior to handing over the hair clipper at aspecialised collection facility, it is necessary

to ensure that the built-in battery is removed. Battery removal will be performed at the

authorised service centre. In the event that the product has been disassembled for the

purpose of ecological disposal then it must not be reassembled.

This symbol indicates that used batteries do not belong in ordinary

municipal waste. Hand over used batteries to designated collection

points for proper disposal. Correct disposal of batteries will help

prevent negative impacts on the environment and human health.

Disposal in other countries outside the European Union.

This symbol is valid in the European Union. If you wish to dispose of

used batteries, request the necessary information about the correct

disposal method from the local authorities or from your vendor.

INSTRUCTIONS AND INFORMATION REGARDING THE

DISPOSAL OF USED PACKAGING MATERIALS

Dispose of used packaging material at asite designated for waste in your municipality.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC

EQUIPMENT

This symbol on products or original documents means that used

electric or electronic products must not be added to ordinary

municipal waste. For proper disposal, renewal and recycling hand over

these appliances to determined collection points. Alternatively, in

some European Union states or other European countries you may

return your appliances to the local retailer when buying an equivalent

new appliance. Correct disposal of this product helps save valuable

natural resources and prevents potential negative effects on the

environment and human health, which could result from improper

waste disposal. Ask your local authorities or collection facility for more details. In

accordance with national regulations penalties may be imposed for the incorrect

disposal of this type of waste.

For business entities in European Union states

If you want to dispose of electric or electronic appliances, ask your retailer or supplier

for the necessary information.

Disposal in other countries outside the European Union.

This symbol is valid in the European Union. If you wish to dispose of this product,

request the necessary information about the correct disposal method from the local

council or from your retailer.

This product meets all the basic requirements of EU directives related to

it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SHP 8400 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SHP 8400 Manual

Product: