Manual Sencor SFS 3050 (page 5 of 6) (English)

758398

Zoom out

Zoom in

1/6

- 5 - 05/2020

EN Electric Food Slicer

User'smanual

■ Prior to using this appliance, please read the user'smanual thoroughly, even in cases,

when one has already familiarised themselves with previous use of similar types of

appliances. Only use the appliance in the manner described in this user’smanual.

Keep this user'smanual in asafe place where it can be easily retrieved for future use.

In the event that you hand this appliance over to somebody else, make sure to also

include this user'smanual.

■ Carefully unpack the appliance and take care not to throw away any part of

the packaging before you find all its parts. We recommend saving the original

cardboard box, packaging material, purchase receipt and responsibility statement

of the vendor or warranty card for at least the duration of the legal liability

for unsatisfactory performance or quality. In the event of transportation, we

recommend that you pack the appliance in the original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Adjustable back plate

A2 Food carriage with thumb guard

A3 Top plate with groove

A4 Base unit

A5 Fixed back plate

A6 Cutting disc

Stainless steel design, cutting disc

diameter 170 mm, removable

A7 Cutting disc central fastener

A8 Food pusher

It is fitted with grip pins to prevent

the food from accidentally slipping

while slicing.

It can be removed from the slicer

when slicing larger pieces of food or

for cleaning purposes

A9 On/Off switch

The switch has three positions:

O– Off.

I– Manual operation. The cutting

disc will rotate while the switch is

pushed down in this position. The

cutting disc will stop when the

switch is released.

II – Continuous operation. The

cutting disc will start rotating and

will run continuously until the

switch is set to position O.

A10 Motor unit

A11 Cutting thickness adjustment knob

Enables variable slicing thickness

adjustment 0-23 mm.

A12 Removable tray

A13 Thickness adjustment knob symbol

for required thickness

A14 Suction cups

BEFORE FIRST USE

■ Before first use, remove all packaging materials including promotion stickers and

labels from the food slicer.

■ Wash the removable parts that come into contact with food (removed cutting disc

A6, food carriage A2, food pusher A8 and removable tray A12) in warm water using

kitchen detergent. Then thoroughly rinse these parts under flowing water and dry

thoroughly with awiping cloth.

■ Using adry or lightly dampened cloth, also clean the outer parts of the appliance

and then wipe it dry. Never submerge the base motor unit in water or any other

liquid!

Attention:

Be careful when handling the cutting disc to prevent injury caused

by the blade.

ASSEMBLY

■ Place the food slicer on an even, dry and stable surface, e.g. on akitchen countertop.

■ Attach the cutting disc to the base motor unit by turning the central fastener A7

fully anticlockwise.

Attention:

When handling the cutting disc use the central fastener. To avoid

injury, do not touch the blade.

■ Place the food carriage on to the top plate with groove and put the food pusher on

to the food carriage.

■ Insert the tray into the bottom part of the base unit. To catch the falling slices of

food, aplate or tray or food-grade foil can be placed on the tray.

OPERATION

Attention:

The slicer is intended for slicing bread, baked goods, smoked

goods, meats, cheeses, vegetables and fruits. Do not use it

for slicing hard baked goods, frozen food, food in plastic or

aluminium foils, meat with bones, fruit with hard stones, etc.

■ Turn the adjustment knob A11 to set the desired slicing thickness. If intending to

slice thin slices or to slice sticky food (e.g. cheeses), it is recommended to slightly

wet the cutting disc.

■ Connect the power cord to an el. power socket.

Attention:

Before connecting the power cord to an electrical power socket,

check that the cutting disc is properly attached to the motor unit.

■ Move the food carriage to the left side of the top plate of the base unit. Place the

food on to the food carriage and push it sideways using the food pusher.

■ Turn the food slicer on with your left hand. The motor unit will start and the cutting

disc will start to rotate.

■ Use your right hand to hold the food carriage and slice the inserted food by moving

towards and away from the cutting disc. Exert aslight pressure on the food while

slicing it to ensure that the food slices are of the same thickness.

Attention:

The slicer can be used with the food carriage without the food

pusher or the entire food carriage can be completely removed.

In both cases it is always necessary to pay increased attention to

avoid injury to the hand or fingers!

■ When you have finished slicing, turn off the slicer and wait until the cutting disc

comes to acomplete stop. Only then may you remove the sliced food from the tray

or any remaining pieces of unsliced food from the food carriage.

Attention:

The slicer is designed for short operation lasting no longer than

5minutes. After this time has elapsed, turn the slicer off and allow

the motor unit to cool down.

Note:

If food sticks to the cutting disc, turn off the food slicer and disconnect

it from the power socket. Clean the cutting disc using aplastic spatula.

Proceed in the same way if any food jams during slicing.

Some food may cause discolouration of plastics. However, this does not

have any effect on the functionality of the food slicer.

■ When you have finished using the slicer, disconnect it from the power socket. Clean

out the slicer according to the instructions in chapter Cleaning and maintenance.

CLEANING AND MAINTENANCE

■ Before cleaning the appliance, always turn it off and disconnect it from the power

socket. Using the adjustment knob, set the adjustable back plate to position 0mm,

i.e. set it to symbol on the adjustment knob A13 on the rear side of the adjustable

back plate.

■ After each use, remove any food remains from the food slicer. Clean parts that

come into contact with food using awiping cloth dipped in clean water and then

dry with awiping cloth. For amore thorough clean, remove the cutting disc, food

carriage, food pusher and removable plate, and wash these parts in warm water

using kitchen detergent. Then thoroughly rinse under flowing water and dry them.

Note:

Remove the cutting disc by turning the central fastener clockwise and

take it off the motor unit.

Attention:

Pay extra attention when handling the cutting disc. To avoid

injury, do not touch the blade.

■ Using adry or lightly dampened cloth, also clean the outer parts of the appliance

and then wipe it dry. Never submerge the base motor unit in water or any other

liquid!

Attention:

For cleaning, do not use thinners, solvents or cleaning agents that

cause abrasion.

STORAGE

■ When not using the food slicer, store it in adry place out of children'sreach.

Attention:

Keep the stored food slicer away from extreme temperatures,

direct sunlight and excessive humidity and do not store it in an

overly dusty environment. Do not place any heavy items on the

stored food slicer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SFS 3050 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SFS 3050 Manual

Product: