Manual Sencor SFN 5011WH (page 8 of 9) (English)

759172

Zoom out

Zoom in

1/9

- 8 - 05/2020

■ The SLEEP mode is a combination of the NATURAL mode (natural breeze) and

agradual lowering of the fan speed.

Fan setting Progression of the SLEEP mode

High speed The appliance will run for 30 minutes in the

NATURAL mode with the high fan speed set.

After 30 minutes, the high fan speed switches to

medium speed. After an additional 30 minutes,

it will switch to the low fan speed setting. The

appliance will remain in the NATURAL mode with

the low fan speed set.

Medium speed The appliance will run for 30 minutes in the

NATURAL mode with the medium fan speed set.

After 30 minutes, the medium fan speed switches

to low speed. The appliance will remain in the

NATURAL mode with the low fan speed set.

Low speed The appliance will run in the NATURAL mode with

the low fan speed set.

Water filter dryer function

■ This function serves exclusively for the purpose of drying out the water filter A10.

If you intend to store and not use the appliance for an extended period of time, it is

necessary to carefully dry out the water filter A10 and other parts to protect them

again the formation of mould.

■ Hold down button B2 for approx. 3 seconds to activate the dryer function. The

fan speed automatically changes to high speed and will run for 20 minutes. During

this time, it is not possible to change the settings of the appliance. Only button

B1 will remain functional. After 20 minutes have elapsed, the appliance will

automatically switch to the stand-by mode.

Note:

If the appliance is turned off with button B1 during the drying out

process, and then is turned on again, the appliance will start at the setting

that was set prior to the dryer function being set.

Setting automatic vertical flap motion

■ Button B6 serves to turn the automatic vertical flap motion on and off. Indicator

light B11 is lit to indicate that motion is activated. Press button B6 again to stop

the vertical motion of the flaps.

Setting the angle of the horizontal flaps

■ The angle of the horizontal flaps A2 can be set manually by tilting them up or down.

When handling them, be careful not to damage them.

Automatic shut-off function

■ The appliance is equipped with an automatic shut-off function after 15 hours of

non-stop operation. This means that after 15 hours of operation, during which no

control button is pressed, the appliance will turn off automatically.

■ If you wish to cancel this function, hold down button B6 for approximately

3 seconds. The appliance will beep and the automatic shut-off function will be

cancelled. If you wish to activate this function again, hold down button B6 for

approximately 3 seconds. The appliance will beep and the function will again be

activated.

Power-saving mode

■ The display will dim out after 1 minute of inactivity. This is normal. Pressing any

button will turn the display on again.

REMOTE CONTROL

■ The function of the buttons on the remote control A15 and the control panel A2 are

the same. If you wish to use the remote control A15, point it at the level of the signal

receiver A1 on the control panel A2. The maximum range of the signal transmitted

from the remote control A15 is 6 m.

Note:

If there are obstacles located between the remote control A15 and the

appliance, the signal may not be transmitted.

FILLING THE WATER TANK

■ Before filling the water tank A12, turn the appliance off, disconnect it from the

power socket and secure the appliance against moving.

■ Release the lock A13 by turning it to the horizontal position – see figure E1.

■ Take out the water tank A12 and fill it with clean cold water – see figure E2.

■ Insert the water tank A12 back into the appliance and turn the lock A13 to the

vertical position to secure the water tank A12 inside the appliance.

■ Always fill the appliance with clean cold water. To prevent undesirable bacteria,

micro-organisms or moulds from multiplying, do not leave water in it for more than

aday.

Warning:

When filling the appliance, make sure that the water level reaches

at least the minimum water level mark and also that it does no go

past the maximum mark.

Note:

When the appliance is used for the first time, you may register aslight

odour or discolouration of the water in the water tank A12. This is

anormal event that will disappear with use and which has no negative

effects on your health.

USING THE COOLING INSERTS

■ The cooling inserts A16 enable the temperature of the water in the water tank to be

reduced, which results in cooler air and faster cooling of the room.

■ Insert the cooling inserts A16 into afreezer for at least 12 hours. Then insert them

into the part of the water tank A12 that is marked with acooling insert symbol. Fill

the water tank A12 with water and insert the cooling insert A12 into the body of

the appliance.

■ The appliance is supplied with two cooling inserts A16, which ensures continuous

operation. You can use either one or both, as required.

Warning:

It is forbidden to open the lock of the cooling insert A16 or to

damage its external case in any way. The contents of the cooling

insert A16 is damaging to health. In the event of swallowing,

immediately seek medical help.

CLEANING AND MAINTENANCE

■ Disconnect the power plug from the power socket before cleaning.

■ For cleaning, do not use cleaning products with an abrasive effect, solvents, etc. that

could damage the appliance.

Warning:

To prevent the risk of injury by electrical shock, do not submerge

the appliance, power cord or power plug in water or any another

liquid.

CLEANING THE WATER TANK

■ When you have finished using the water tank A12, empty it out and rinse it with

clean water.

■ To remove limescale deposits and to prevent undesirable bacteria, micro-organism

or moulds from multiplying inside the water tank A12, clean it out at least once

per month using acloth dampened in lukewarm water with the addition of neutral

detergent. Then rinse it out thoroughly using clean water, dry it out using aclean

cloth.

CLEANING THE DUST AND WATER FILTER

■ Dirt and soils may accumulate on the dust filter A9 and water filter A10 during use,

which may negatively affect the operation of the appliance. We recommend that

these filters are regularly cleaned at least 1x per month. The frequency with which

the appliance is cleaned depends on its use. If it becomes excessively soiled, the

effectiveness of the appliance may be reduced.

1. Disconnect the power plug from the power socket.

2. Press the safety clip at the top of the dust filter A9 and tilt it out of the appliance

together with the water filter A10 – see figure F1.

3. Carefully take out both filters – see figure F2.

4. Take the water filter A10 out of the dust filter A9.

5. Wipe the dust filter A9 with asoft sponge lightly dipped in warm water with asmall

amount of neutral cleaning agent.

6. Soak the water filter A10 in warm water with asmall amount of neutral cleaning

agent. Then carefully wring it out in your hands and install it back into the dust filter

A9.

7. Insert both filters back into the appliance and turn on the dryer function (see

instructions in section "Water filter dryer function").

CLEANING THE OUTER CASE

■ To clean the outer case, use atextile lightly dampened in lukewarm water with an

addition of neutral detergent.

Storage

■ When not using the appliance for an extended period of time, disconnect the power

plug from the power socket and clean it according to the instructions in chapter

"Cleaning and maintenance".

■ Before storing it, check that the appliance and all its accessories are thoroughly

clean and dry.

■ Remove the battery from the remote control A14.

■ Store the appliance in a dry, clean and well-ventilated location not exposed to

extreme temperatures and out of children'sreach.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SFN 5011WH in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SFN 5011WH Manual

Product: