759913
5
Zoom out
Zoom in
Previous page
1/6
Next page
03/2017
- 5 -
Copyright © 2017, Fast ČR, a.s.
EN Desktop Fan
User'smanual
Prior to using this appliance, please read the user’smanual
thoroughly, even in cases, when one has already familiarised
themselves with previous use of similar types of appliances.
Only use the appliance in the manner described in this
user’smanual. Keep this usersmanual in asafe place where it
can be easily retrieved for future use.
■ We recommend saving the original cardboard box, packaging
material, purchase receipt and responsibility statement of the
vendor or warranty card for at least the duration of the legal
liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance
in the original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Front protective grill
A2 Fan blades with adiameter of 23 cm
A3 Nut for fastening the rear protective grill
A4 Rear protective grill with fastening clamps and acarry
handle
A5 Motor unit shaft
A6 Horizontal oscillation toggle switch
A7 Motor unit with adjustable vertical tilt angle
A8 Panel with control buttons
0 – o, 1 – low speed, 2 – high speed
A9 Base
Note:
The accessories include ascrew and anut for joining the protective
grills.
BEFORE FIRST USE
■ Take the appliance and its accessories out of the packaging
materials. Before disposing of the packaging materials, make
sure that no part of the appliance is missing.
ASSEMBLING AND DISASSEMBLING THE APPLIANCE
■ Insert the control panel A8 from above into the base A9 and
make sure that it is properly seated inside. Grasp the fan under
the motor unit A7 and turn it upside down. Turn the wing nut
located underneath the control panel A8 by 90° to secure the
panel A8 to the base A9 (see g. B). Turn the fan back over to
the operating position and stand it on astraight, clean, dry,
stable and smooth surface.
■ Place the rear protective grill A4 against the front side of the
motor unit A7 so that the handle is above the motor unit A7
and that the alignment tabs on the front side of the motor unit
A7 slide into the respective holes in the rear grill A4. Place the
nut A3 on to the shaft A5 and screw it in clockwise to secure the
rear protective grill A4 to the motor unit A7. Before tightening
the nut A3, make sure that the rear grill A4 has not moved and
that the alignment tabs are still in the respective holes.
■ On to the shaft of the motor unit A5 put on the fan blades A2
so that the shaft A5 properly slides into the centre part of the
fan blades A2. Push the fan blades A2 towards the motor unit
A7 all the way. Now check that the fan blades A2 turn freely.
■ Release the clamps along the perimeter of the rear protective
grill A4. Place the front protective grill A1 against the rear
protective grill A4 so that the front grill A1 fits into the
alignment hook in the bottom part of the rear protective grill
A4 and that the screw holes at the top of both grills are aligned.
Fasten the released clamps along the perimeter of the grills. To
ensure astrong connection of the two grills, into the holes at
the top of the grills it is necessary to screw in the supplied screw
and secure it with the nut.
■ Before putting the fan into operation, check that it is correctly
assembled and that the protective grills are rmly joined.
■ To disassemble, proceed in reverse sequence.
OPERATING THE APPLIANCE
Setting the speed and turning o the fan
Locate the fan on an even, dry and smooth surface within reach
of apower socket. Connect the power cord to apower socket.
To set the air ow speed, use the buttons on the control panel
A8. The functions of the control buttons are described below:
0 – turn o the fan;
1– set alow air ow speed;
2– set ahigh air ow speed.
When you have nished using the fan, always turn it o and
disconnect it from the power socket.
Setting horizontal oscillation
■ The horizontal oscillation of the motor unit A7 can be set using
the toggle switch A6. To start the horizontal oscillation, push
the toggle switch A6 down. The motor unit A7 will oscillate
from side to side at an angle of approximately 90°.
■ To turn o the oscillation, pull the toggle switch A6 up. This will
turn o the oscillation.
Setting the vertical tilt angle of the motor unit
■ Before setting the vertical tilt angle of the motor unit A7, rst
turn o the fan. Set the desired angle of the motor unit A7 and
then you may start the fan again.
Note:
The motor unit A7 may only be tilted up and down in
alimited range. Do not set the tilt angle of the motor unit
A7 by force.
CLEANING AND MAINTENANCE
■ Before cleaning it, make sure that the appliance is turned o
and disconnected from the power socket.
■ Regularly remove dust from the appliance. For normal cleaning,
aclean, dry cloth is sucient. In the event that it is dirtier,
disassemble the appliance and wipe the individual parts
with awiping cloth slightly dampened in asolution of warm
water and neutral detergent. Then wipe everything so that it is
thoroughly dry. Make sure that no water enters the motor unit
A7 or into the control panel A8 while cleaning.
■ Prior to reassembly, make sure that all parts of the appliance
are dry.
■ Do not submerge the appliance or its power cord in water and
do not wash it under running water.
■ For cleaning do not use steel wool, cleaning products with an
abrasive eect, petrol and other solvents.
STORAGE
■ If you will not be using the fan for an extended period of time,
store it in aclean, dry place or disassemble it and put it back
into the box.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SFE 2311 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SFE 2311 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sencor SFE 2311

Sencor SFE 2311 User Manual - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info