Manual Sencor SES 9200CH (page 9 of 12) (English)

758389

Zoom out

Zoom in

1/12

- 9 - 06/2020

Note:

Perform the rinsing process also when you have not used the espresso

machine for an extended period of time.

The pump will make anoise during the water dispensing process. This

is normal.

Brewing an espresso

1. Place acup, mug or glass underneath the brewing head A8. Set the height of the

brewing head A8 by sliding it up or down depending on the size of your cup, mug

or glass – see figure F. If the cup or glass is too tall, you may remove the outer drip

tray A11. After removing the cup or glass, return the drip tray A11 to its place.

2. Press button B12 and the button will be backlit.

3. The espresso machine will automatically start the coffee grinding, dosing and

tamping process, and will dispense it.

4. As soon as the espresso machine has finished dispensing the coffee, it will

automatically switch to the stand-by mode.

Brewing latté macchiato / cappuccino

1. Set up the system for automatic frothing as described in section "Setting up the

system for automatic frothing".

2. Pour milk into the milk jug A13. Put on the lid A14 and ensure that it is firmly seated.

Note:

To achieve a rich and creamy foam, it is recommended to use properly

cooled milk (approx. 5°C) with aminimum fat content of 3%.

3. Place acup, mug or glass underneath the brewing head A8. Set the height of the

brewing head A8 by sliding it up or down depending on the size of your cup, mug

or glass – see figure F. If the cup or glass is too tall, you may remove the outer drip

tray A11. After removing the cup or glass, return the drip tray A11 to its place.

4. Press button B11 to brew a latté macchiato or button B10 to brew

acappuccino. Press button to confirm.

5. The espresso machine will automatically start the latté macchiato or cappuccino

brewing process.

6. As soon as the espresso machine has finished brewing the coffee, it will

automatically switch to the stand-by mode.

7. Disconnect the connecting tube A15 from the hole in the brewing head A8 and

place the milk in arefrigerator. To prevent milk from leaking out of the tube A15,

wind it around the lid A14 – see figure G.

Frothing milk

1. Set up the system for automatic frothing as described in section "Setting up the

system for automatic frothing".

2. Pour milk into the milk jug A13. Put on the lid A14 and ensure that it is firmly seated.

Note:

To achieve a rich and creamy foam, it is recommended to use properly

cooled milk (approx. 5°C) with aminimum fat content of 3%.

3. Place acup, mug or glass underneath the brewing head A8. Set the height of the

brewing head A8 by sliding it up or down depending on the size of your cup, mug

or glass – see figure F. If the cup or glass is too tall, you may remove the outer drip

tray A11. After removing the cup or glass, return the drip tray A11 to its place.

4. Press button B11 twice to brew alatté macchiato or button B10 to brew

acappuccino. Press button to confirm.

5. Press the button again when there is asufficient amount of frothed milk in the cup.

6. The espresso machine will then automatically switch to the standby mode.

7. Disconnect the connecting tube A15 from the hole in the brewing head A8 and

store the milk in arefrigerator. To prevent milk from leaking out of the tube A15,

wind it around the lid A14 – see figure G.

Dispensing hot water

1. Place acup, mug or glass underneath the brewing head A8. Set the height of the

brewing head A8 by sliding it up or down depending on the size of your cup, mug

or glass – see figure F. If the cup or glass is too tall, you may remove the outer drip

tray A11. After removing the cup or glass, return the drip tray A11 to its place.

2. Press button B9 twice. The button's backlight will be lit and the espresso

machine will start dispensing hot water.

3. The dispensing of hot water will stop automatically and the button'sbacklight will

turn off.

Note:

If you need to stop the dispensing of hot water sooner, press button B9

once and the water dispensing process will stop.

USER SETTINGS

Setting the amount of ground coffee

■ Use the ground coffee amount adjustment when the brewed coffee is too strong

or too weak.

■ Button B8 serves to adjust the amount of ground coffee.

■ Based on personal preferences, select the amount of ground coffee by repeatedly

pressing button B8 : small (approx. 7 g), medium (approx. 8 g) or large

(approx. 10 g).

Setting the dispensed coffee volume

■ The espresso machine enables the volume of dispensed coffee to be adjusted

according to your preferences. The settings you make will be saved to the memory

of the espresso machine.

1. Place acup, mug or glass underneath the brewing head A8.

2. Turn on the espresso machine by pressing button B7 .

3. Press the button of the beverage that you wish to brew: button B12 for

brewing avolume of espresso or button B11 for brewing alatté macchiato or

button B10 for brewing acappuccino. Press button to confirm.

4. As soon as the espresso machine starts dispensing frothed milk, hold down the

button of the selected beverage until the required volume of frothed milk pours

into the cup. Release the button, two beeps will be made and the volume of frothed

milk will be saved to the memory of the appliance.

5. When as the espresso machine starts dispensing coffee, hold down the button

of the selected beverage until the required volume of coffee pours into the cup.

Release the button, two beeps will be made and the volume of coffee will be saved

to the memory of the appliance.

Hot water settings

1. Place acup, mug or glass underneath the brewing head A8.

2. Turn on the espresso machine by pressing button B7 .

3. Press button B9 twice. The button will be backlit.

4. As soon as the espresso machine starts dispensing hot water, hold down button B9

until the required volume of hot water pours into the cup. Release the button

and the volume of hot water will be saved to the memory of the appliance.

Note:

To restore the default volume settings for dispensed coffee and hot water,

proceed according to the instructions in section "Setting the mode".

Setting the mode

■ The appliance can be set to an ECO mode, afast mode or the default factory settings.

In ECO mode, greater power savings are achieved. In the fast mode, the coffee is

prepared faster than with the default factory settings.

ECO mode Fast mode Default

settings

Indicator light No Yes Yes

Pre-steam * Yes No Yes

Automatic shut-off time 10 minutes 30 minutes 20 minutes

Option to set the

dispensed coffee volume Yes Yes Yes

*Note:

The pre-steam function means that the ground coffee is first steamed with

asmall amount of water. This will cause the coffee to swell and thereby

when it is subsequently fully steamed, its flavour will be developed fully,

and its aromatic compounds and essential oils will be fully extracted.

1. In the stand-by mode, press and hold down button B7 for 5 seconds. Button B7

will start flashing and at the same time other buttons will also be flashing or lit

depending on the mode that is set.

Cappuccino

button Latté button Espresso button

ECO mode Lit Flashing Flashing

Fast mode Flashing Lit Flashing

Default settings Flashing Flashing Lit

2. To set the ECO mode, press button B10 , to set the fast mode press button B11

and to reset to default settings, press button B12 . After setting amode, 2

beeps will be made. In the event that you attempt to set amode that is already set,

the appliance will not react to the button being pressed.

3. If you do not wish to change the mode settings, press button B7 once more,

or wait 5 seconds until the appliance automatically switches back to the stand-by

mode.

CLEANING AND MAINTENANCE

■ Disconnect the power plug from the power socket and allow the appliance to cool

down before cleaning it.

Warning:

For cleaning, do not use cleaning products with an abrasive effect,

solvents, etc. that could damage the appliance. No part of this

appliance is intended for washing in adishwasher.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SES 9200CH in the language / languages: English as an attachment in your email.

The manual is 3,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SES 9200CH Manual

Product: