758392

Sencor SES 4900SS Manual

8
Zoom out
Zoom in
Previous page
1/9
Next page
- 8 - Copyright © 2020, Fast ČR, a.s. 12/2020
Note:
The factory settings remain permanently set in memory
even when you adjust the volume of the brewed coffee.
If you need to restore the original settings, perform the
factory reset – see part “Restoring factory settings”.
■ The volume of the brewed coffee can be set for one or two cups
within the range specified in the table below.
Factory set value Minimum volume Maximum
volume
1 cup 40 ml 20 ml 150 ml
2 cups 125 ml 40 ml 300 ml
■ If you prefer the Long Black coffee style, adjust the volume of the
brewed coffee based on personal preferences so that you do not need
to dilute the coffee with hot water. The espresso machine will brew
the adjusted volume of brewed coffee automatically, nevertheless it
is necessary to adjust the amount of ground coffee to the newly set
volume so that the resulting coffee is not too weak.
Note:
If you have adjusted the volume of brewed coffee to the
maximum volume and occasionally need to brew an
espresso type coffee in asmaller volume of brewed coffee,
it will be necessary to perform afactory reset.
1. Insert the strainer into the portafilter A11 (without ground coffee)
and then insert the portafilter A11 into the brew head A12. Place
acup or mug underneath the brew head A12.
2. Ensure that there is asufficient amount of water in the water tank
A5. The water must cover the minimum water level mark.
Programming the volume for asingle cup:
Hold down the one-cup brew button B2. Keep the button B2 held
down until your preferred amount of water flows into the cup or
mug. Releasing the button B2 will automatically stop the brewing
process and the new volume will be saved to memory.
3. Programming the volume for two cups:
Hold down the two-cup brew button B3. Keep the button B3 held
down until your preferred amount of water flows into the cup or
mug. Releasing the button B3 will automatically stop the brewing
process and the new volume will be saved to memory.
Note:
The adjusted brewed coffee amount will be saved to
memory until a factory reset is performed or until the
power cord plug is removed from the power socket.
Restoring factory settings
■ In the event that aproblem arises resulting from the settings you have
made, it is necessary to perform afactory reset.
Attention:
Restoring factory settings will delete all the settings
performed by you and restore them to the values set
at the factory. The set water hardness values will also
be deleted. Then it will be necessary to again perform
all the necessary settings.
1. Check that the power cord plug is connected to apower socket.
2. Check that the appliance is turned off.
3. Simultaneously hold down all four buttons (B1, B2, B3, B4) for 5
seconds until all the buttons start flashing. Then you can release
the buttons.
4. The factory reset has been performed.
CLEANING AND MAINTENANCE
■ Disconnect the power plug from the power socket and allow the
appliance to cool down before cleaning it.
■ For cleaning, do not use cleaning products with an abrasive effect,
solvents, etc. that could damage the appliance. No part of this
appliance is intended for washing in adishwasher.
Warning:
To prevent the risk of injury by electrical shock, do not
submerge the appliance, power cord or power plug in
water or any another liquid.
Cleaning the drip tray and grate
■ Carefully remove the drip tray A8 together with the grate A9. Pour out
the water and rinse the drip tray A8 and grate A9 with warm water.
Wipe dry and then reinsert into the espresso machine.
■ In the event that the tray A8 and grate A9 are heavily soiled, wash
them in warm water with a small amount of neutral dishwashing
detergent, rinse them and wipe them dry.
Cleaning the baskets and the portafilter
■ Clean the baskets and the portafilter A11 after every use. Rinse out
the basket and portafilter A11 under warm water and wipe dry.
■ If the holes in the basket are clogged, clean them out using the
supplied cleaning tools.
Cleaning the brew head
■ After brewing approximately 200 coffees, it is necessary to rinse out
the brew head A12. Fill up the water tank A5 with cold water. Turn
on the espresso machine and wait until it heats up to operating
temperature.
■ Press button B2 or B3 and allow about 0.5 litres of water to
flow through the brew head A12.
Attention:
When rinsing it out, it is important that the portafilter
and basket are NOT inserted.
Cleaning the outer surface
■ Wipe the outer surface of the appliance with alightly dampened cloth
and then wipe it thoroughly dry.
Cleaning the water tank
■ At least once per month, clean out the water tank A5 and lid A4. Rinse
it out using clean water with the addition of asmall amount of neutral
kitchen detergent. Then rinse it out thoroughly using clean water, dry
it and put it back in its place.
Descaling
■ When the descaling indicator light A14 is lit, it is necessary to perform
the descaling process.
■ Use a descaling agent specifically intended for descaling espresso
machines that is commonly sold in retail chains.
1. Prepare the descaling agent according to the instructions on the
packaging of the descaling agent.
2. Pour the prepared solution into the water tank A5 up to the max.
mark.
3. Insert the plug on the power cord into apower socket and press
the button B1 to turn on the espresso machine. Button B1 will
start flashing, which means that the espresso machine is heating
up to operating temperature.
4. Make sure that the portafilter A11 is not installed in the brew head
A12.
5. Place a container for capturing the water underneath the steam
nozzle A7.
6. When button B1 stops flashing, turn the control knob A6 to
symbol and the heated solution will start being dispensed.
7. Allow the solution to flow out through the steam nozzle A7 until
the dispensing stops automatically.
8. Turn the control knob A6 to symbol .
9. Now move the container underneath the brew head A12.
Note:
If necessary pour the solution out of the container.
Nevertheless, be very careful as the solution in the
container is very hot.
10. Press button B3 and the espresso machine will start dispensing
the solution through the brew head A12.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SES 4900SS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SES 4900SS in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info