Manual Sencor SCW 3001 (page 5 of 6) (English)

759155

Zoom out

Zoom in

1/6

02/2017

- 5 -

EN Window Cleaner

User'smanual

■ Prior to using this appliance, please read the user’s manual

thoroughly, even in cases, when one has already familiarised

themselves with previous use of similar types of appliances. Only use

the appliance in the manner described in this user’s manual. Keep

this user’smanual in asafe place where it can be easily retrieved for

future use.

■ We recommend saving the original cardboard box, packaging

material, purchase receipt and responsibility statement of the

vendor or warranty card for at least the duration of the legal

liability for unsatisfactory performance or quality. In the event of

transportation, we recommend that you pack the appliance in the

original box from the manufacturer.

DESCRIPTION OF THE APPLIANCE AND ACCESSORIES

A1 Removable rubber

squeegee

A2 Suction opening

A3 Removable suction nozzle

A4 Suction nozzle release

button

A5 LED battery power and

charging indicator

A6 Vents

A7 Body of the appliance

A8 On/Off button of the

appliance

A9 Removable dirty water tank

A10

Handle

A11

Tank release button

is located on both sides of the

handle.

A12

Folding stand

A13 Tank drain valve

A14 Power adapter socket

is fitted with aclosable plug.

A15 Textile mop sleeve

A16 Wiping attachment

A17 Spray nozzle

A18 Detergent spray trigger

A19 Spray tank

A20 Power adapter

ASSEMBLING AND DISASSEMBLING APPLIANCE

Window cleaner

■ Assemble the window cleaner by attaching the suction nozzle A3 to

the body of the appliance A7 and slide on the rubber squeegee A1

from the side into the groove located in the suction opening A2. The

correct connection of the nozzle A3 is indicated by an audible click.

Insert the removable tank A9 into the body of the appliance A7 with

first the top part of the tank A9 sliding into the area from underneath

the handle A10. Then push the bottom part of the tank A9 into the

area from underneath the handle A10 until the entire tank A9 fits in

its place. Make sure that the tank drain valve A13 is properly closed.

■ Disassemble in reverse sequence. To remove the tank A9, it is

necessary to press buttons A11 while at the same time releasing the

bottom end of the tank A9 and then pull it away from the body of the

appliance A7 to remove the entire tank A9.

The sprayer

■ Assemble the sprayer by screwing the spray nozzle on to the spray

tank A19. Attach the textile mop sleeve A15 on to the wiping

attachment A16.

■ Disassemble the the sprayer in the reverse sequence.

FILLING THE SPRAYER

■ Fill the spray tank A19 with asolution of water and asmall amount

of detergent (alcohol-free). When diluting concentrated cleaning

agents, follow the instructions on their packaging.

■ Fill the spray tank A19 with water at atemperatures of up to 40 °C.

Using water that is too hot could result in deformation of the tank.

■ After filling up, attach the spray nozzle to the tank.

CHARGING THE APPLIANCE

■ The window cleaner has a built-in Li-Ion battery that needs to be

charged before the appliance is used.

■ Check that the window cleaner is turned off. Plug the power adapter

connector A20 into the socket A14. Plug the adapter plug A20 into

apower socket.

■ After connecting to a power socket, the LED indicator A5 will be

lit red. This signals that the battery is being charged. Afull charge

requires approximately 4 hours. The actual charging time depends

on the power level of the battery.

■ Once the changing process is complete and the battery is fully

charged, the LED indicator A5 will be lit blue. Disconnect the

window cleaner from the power adapter A20 and disconnect the

adapter plug A20 from the power socket.

■ After disconnecting from the power adapter A20, cover the socket

A14 with the plug to prevent the entry of water or humidity.

■ Afully charged window cleaner will run for approximately 20 minutes.

Then it is necessary to recharge it.

OPERATING THE APPLIANCE

■ Use the appliance at an ambient temperature between 5 and 40 °C.

Make sure that the window cleaner is properly assembled and fully

charged.

■ To apply the cleaning agent, press the spray trigger A18 and evenly

spray the given surface with the detergent solution. Wipe the soiled

areas with the textile mop sleeve A15. Now put the spray aside and

pick up the window cleaner.

■ Start the window cleaner by pressing button A8. Place the suction

opening A2 with the squeegee A1 on to the surface on to which

the detergent solution was previously applied, and pull the window

cleaner to travel over this surface and vacuum away the detergent

solution from the cleaned surface. You can travel over the surface up

and down or side to side.

Note:

If you do not wish to use the sprayer, you may apply the

cleaning agent in the normal manner.

■ Regularly check the liquid level inside the tank A9. If it reaches the

maximum mark, turn off the window cleaner by pressing button

A8. Hold the window cleaner in ahorizontal position above asink

or wash basin, and open the drain valve A13. Once the tank A9 is

empty, close the drain valve A13, and you may continue cleaning.

■ In the event that battery voltage declines during operation, the LED

indicator A5 will start flashing red for awhile and then turn off. The

window cleaner will automatically turn off to prevent damaging the

built-in battery by completely discharging it. To charge the battery,

follow the instructions described in chapter Charging the appliance.

■ When you have finished using the window cleaner, always turn it off

by pressing button A8, clean it out and allow it to recharge for the

next use.

MAINTENANCE AND CLEANING

■ Before cleaning it, always make sure that the window cleaner is

turned off and disconnected from the power socket.

■ Disassemble the suction nozzle A3 from the body of the window

cleaner A7. Clean it with a dampened cloth with an addition of

neutral cleaning agent, and then rinse it under clean running water.

Allow it to dry naturally or wipe it dry.

■ Remove the tank A9 from the body of the window cleaner A7. Over

asink or wash basin, open the drain valve A13 and empty out the

tank A9. Then rinse it out thoroughly with clean water. Wipe its

surface dry and allow it to dry naturally. Thoroughly and regularly

clean the tank A9 after every use. The dirt accumulated inside the

tank A9 has an effect on the functionality of the appliance.

■ Remove any remaining cleaning solution from the spray tank A19.

Rinse out the tank A19 with clean water and allow it to dry naturally.

■ Remove the textile mop sleeve A15 from the attachment A16 and

wash it under running water with the addition of asmall amount

of detergent and then rinse under clean running water. Allow it to

dry naturally. You may also wash the textile mop sleeve in awashing

machine at a temperature of up to 60 °C, but do not use a fabric

softener.

■ If the rubber squeegee A1 or the textile mop sleeve A15 show signs

of wear, replace these parts with new ones. Spare parts are available

at brick and mortar stores, and online stores. For replacement, it is

necessary to pull the rubber squeegee A1 outwards from the side

of the suction nozzle A3 and to insert anew squeegee in its place.

■ Prior to assembly, make sure that all parts of the appliance are dry.

■ For cleaning the appliance, do not use steel wool, abrasive cleaning

products, solvents, etc.

■ Do not submerge the body of the appliance A7 in water or any other

liquid and do not rinse it under running water.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SCW 3001 in the language / languages: English as an attachment in your email.

The manual is 2,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sencor SCW 3001

Sencor SCW 3001 User Manual - Dutch - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SCW 3001 Manual

Product: