757104
6
Zoom out
Zoom in
Previous page
1/17
Next page
EN - 4
5. INSTALLATION/CONNECTION
Basic procedure:
1. Pull the key out of the ignition and then disconnect the terminal on the car battery.
2. Correctly connect the input and output wires.
3. Install the device into the motor vehicle.
4. Reconnect the terminal on the car battery.
5. Reset the device.
Warning:
This device may only be installed in a motor vehicle with a 12 V DC power supply and
a grounded negative pole.
If you connect the ignition wire (red) and the battery wire (yellow) to the vehicle's chassis
(grounding), you may cause a short circuit, which may subsequently cause a fi re. Always
connect these wires to the power source via a fuse box.
Prior to installing the device, disconnect the negative battery terminal and perform all
electrical connections.
Insulate unconnected wires using vinyl tape or another similar material. To prevent
a short circuit, do not remove the covers on the ends of unconnected wires or terminals.
After installation, do not forget to ground this device again to the vehicle's chassis.
If the power supply is not turned on, the cause may be a short circuit of the speaker wire
or its contact with the chassis of the vehicle and the activation of the protective function.
Therefore, it is necessary to check the speaker wire.
Attention:
If your vehicle's ignition does not have the ACC position, connect the ignition wire to the
power source that can be turned on and off using the ignition key. If you connect the
ignition wire to the power source with a constant voltage supply, e.g. battery wires, this
may discharge the battery.
Install this device into the console of your vehicle. Make sure that the front panel does
not hit the lid of the console (if one exists) when opening and closing.
After installing the device, check that your vehicle's brake lights, blinkers, wipers, etc.
are working correctly.
Mount the device horizontally or at an incline of no more than 30°.
In the event that the fuse melts, fi rst make sure that the wires are not in contact and are
not causing a short circuit, and then replace the old fuse with a new one with the same
nominal values.
Connect the speaker wires correctly to the respective terminals. If sharing wires or if
you ground them to any metal part of the motor vehicle, the device may be damaged or
it may not function incorrectly.
If you connect only two speakers to the system, connect them either only to the front
output or only to the rear output (do not combine the front and rear output).
The installation and connection of this product required skill and experience. For reasons
of safety, have this work performed by professionals.
If you come across any problems during the installation, please contact a Sencor vendor.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SCT 5051BMR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SCT 5051BMR in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info