758827

Sencor SBL 5371 Manual

7
Zoom out
Zoom in
Previous page
1/10
Next page
Stand Mixer
SBL 5370WH / SBL 5371BK / SBL 5372RD
EN
EN-7
2016 08/2016
BEFORE FIRST USE
1. Take the appliance and its accessories out of the packaging materials.
2. All parts (lid insert A1, lid A2 with sealing ring A3, blending jar A4, blade assembly sealing ring
A5, blade assembly A6, attachment collar A7 and grinders Aqd and Aqf), which are designed for
contact with food, must be washed thoroughly using hot water and a neutral kitchen detergent.
Then rinse them under clean running water and thoroughly wipe dry with a fine wiping cloth or
allow them to dry naturally.
Attention:
When cleaning the blade assembly take special care to avoid injury. The blades are sharp.
ASSEMBLING AND DISASSEMBLING THE APPLIANCE
• Before you start assembling or disassembling the appliance, check that the motor unit A0 is turned
off and disconnected from the power socket and that the rotating parts have come to a complete
stop.
1. Assembling and disassembling the blending jar
1.1 Place the blade assembly A6 into the attachment collar A7. Place the sealing ring A5 on the
blade assembly A6, and make sure it adheres along its entire perimeter to the blade assembly A6.
1.2 Place the attachment collar A7 with inserted blade assembly A6 and sealing ring A5 on the
blending jar A4 from the bottom. Screw the collar A7 to the jar A4 and tighten firmly.
1.3 Insert the lid insert A1 into the opening of the lid A2 and turn clockwise to secure it. When you
have placed all the necessary ingredients into the blending jar A4, close it with the assembled lid.
The lid needs to be properly pushed down along the entire perimeter so that it adheres well to the
edge of the blending jar A4.
1.4 When disassembling the blending jar, proceed in the reverse sequence.
2. Attaching the blending jar to the motor unit and its removal
2.1 Place the motor unit A0 on an even, dry surface, for example on a kitchen countertop. Place the
assembled blending jar on to the motor unit A0 and press it down to assure its securing to the
motor unit A0. The assembled blending jar can be seated on the motor unit A0 in two directions.
The handle faces either right or left.
2.2 To remove, simply lift up the blending jar A4.
OPERATING THE APPLIANCE
1. Make sure that the speed dial A9 is set to position OFF and that the motor unit A0 is disconnected
from the power socket.
2. Assemble the blender according to the instructions in the chapter Assembling and disassembling
the appliance.
3. Place the food or pour the liquids that you wish to blend into the blending jar A4. Close the
blending jar A4 tightly using the lid according to the instructions in the chapter Assembling and
disassembling the appliance.
Note:
The maximum capacity of the blending jar A4 is 1.5l. We do not recommend filling the blending
jar with an amount of fluid greater than 1.2l. Fluids that take up more volume while blending
are best prepared in smaller batches.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SBL 5371 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SBL 5371 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info