■Repeatedly press button MODE C13 until the cooling indicator C2 is lit. Use buttons –/+ C10 aC11 to set the desired temperature. You can set the temperature in the range
from 18 to 32 °C.
■Using button FAN C9, set the fan speed. Repeatedly press button FAN C9 to switch the speed in the following order: High (high speed) – Medium (medium speed) – Low (low
speed) – Auto (automatic speed). Each time the button is pressed, the respective indicator will be lit on the control panel.
2. Heating mode (only models SAC MT1224CH and SAC MT1225CH)
■Repeatedly press button MODE C13 until the heating indicator C1 is lit. Use buttons –/+ C10 aC11 to set the desired temperature. You can set the temperature in the range
from 13 to 27 °C.
■Using button FAN C9, set the fan speed. Repeatedly press button FAN C9 to switch the speed in the following order: High (high speed) – Medium (medium speed) – Low (low
speed) – Auto (automatic speed). Each time the button is pressed, the respective indicator will be lit on the control panel. The air conditioner will start heating within afew
minutes. The fan may run in short intervals even when the temperature has been reached.
■During the heating mode, water will condense from the air in the air conditioner and accumulate in the internal condensate tank. When the condensate tank is full, the display
C6 will show (full condensate tank) and it will be necessary to remove the water from the condensate tank. Proceed according to the instructions in section “Condensate
drain outlet” later in this user’smanual. Once the condensate tank is empty, the air conditioner will start running again.
Note:
In the event that the air conditioner is located in avery cold room, the air conditioner will defrost automatically. It may stop running temporarily. The display C6 will show
. Likewise, you may register an increased noise level. This is normal.
3. Fan mode
■Repeatedly press button MODE C13 until the fan mode indicator C4 is lit. Using button FAN C9, set the fan speed. Repeatedly press button FAN C9 to switch the speed in the
following order: High (high speed) – Medium (medium speed) – Low (low speed). Each time the button is pressed, the respective indicator will be lit on the control panel and,
likewise, agraphical indicator will show the selected speed on the display C6. In this mode, it is not possible to set the temperature, nor is it necessary to connect the flexible
hose B1 to the portable air conditioner.
4. Dehumidification mode
■Make sure that the flexible hose B1 is connected to the air conditioner and goes into the window. Repeatedly press button MODE C13 until the dehumidification indicator C3 is
lit. The display C6 will show . It is not possible to set the temperature or fan speed in this mode. The fan speed is automatically set.
Functions of the portable air conditioner
1. Automatic start function
■
Start the portable air conditioner by pressing button POWER C8. Using button MODE C13, select the operating mode in which you wish to turn on the portable air conditioner. Use
buttons –/+ C10 and C11 to set the desired temperature and use button FAN C9 to select afan speed as required. Turn off the portable air conditioner using button POWER C8.
■Now press button TIMER C12, awristwatch icon together with aflashing time will appear on the display C6. Use the buttons –/+ C10 andC11 to set the time after which the
portable air conditioner will turn on automatically. The automatic start time can be set in the range between 30 minutes and 24 hours (set in 30 minute intervals until 10 hours,
and one hour intervals until 24 hours).
■After afew seconds, the time is saved to the memory of the air conditioner and the automatic start indicator appears on the display C6. Once the set time elapses, the portable
air conditioner will start automatically.
■If button TIMER C12 or POWER C8 are pressed after the automatic start is set, then this setting will automatically be cancelled.
2. Automatic shut-off function
■When the portable air conditioner is running, press button TIMER C12, awristwatch icon together with aflashing time will appear on the display C6. Use the buttons –/+ C10
andC11 to set the time after which the portable air conditioner will automatically stop.
■The automatic shut-off time can be set in the range between 30 minutes and 24 hours.
■
After afew seconds, the time is saved to the memory of the air conditioner and the automatic shut-off indicator appears on the display C6. Once the set time elapses, the portable
air conditioner will shut off automatically.
■If button TIMER C12 or POWER C8 are pressed after the automatic shut-off is set, then this setting will automatically be cancelled.
B. REMOTE CONTROL
Inserting and replacing batteries
■Slide out the battery compartment cover, which is located on the rear side of the remote control. Place two AAA/LR03 (2× 1.5 V) alkaline batteries into the battery compartment
and close the cover.
■When inserting the batteries ensure the correct polarity as shown in the battery compartment.
■When replacing the batteries, always use batteries of the same type, never combine old and new batteries or batteries of various types.
Note:
Removing the batteries from the remote control will delete all the settings. After new batteries are inserted the default remote control settings as programmed by the
manufacturer will be renewed.
■If you will not be using the remote control for longer than 2 months, remove the batteries.
Using the remote control
■For the remote control to work correctly, ensure that the maximum distance of the remote control from the portable air conditioner is not greater than 7 m and that there is no
obstacle between the remote control and the portable air conditioner that could prevent the transmission of the signal.
■Point the remote control directly at the portable air conditioner. The transmission of the signal is confirmed by ashort sound signal.
■Do not expose the remote control to direct sunlight or high temperatures. Otherwise the signal may not be transmitted.
Turning the portable air conditioner on and off
■To turn on the portable air conditioner, press button D2 once. Press button D2 again to turn the portable air conditioner off.
Operating modes
1. Cooling mode
■
Repeatedly press button MODE D3 until the arrow on the display D1 stops at symbol . Use buttons ▲/▼D7 and D8 to set the desired temperature. You can set the temperature
in the range from 18 to 32 °C.
■Use button FAN D9 to set the fan speed. Repeatedly press button FAN D9 to switch the speed in the following order: High (high speed) – Medium (medium speed) – Low (low
speed) – Auto (automatic speed). Each time the button is pressed, the arrow at the speed bar on the display D1 will switch.
2. Heating mode (only models SAC MT1224CH and SAC MT1225CH)
■Repeatedly press button MODE D3 until the arrow on the display D1 stops at symbol .
■Use buttons ▲/▼D7 and D8 to set the desired temperature. You can set the temperature in the range from 10–25 °C.
■Use button FAN D9 to set the fan speed. Repeatedly press button FAN D9 to switch the speed in the following order: High (high speed) – Medium (medium speed) – Low (low
speed) – Auto (automatic speed). Each time the button is pressed, the arrow at the speed bar on the display D1 will switch.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sencor SAC MT1224CH at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sencor SAC MT1224CH in the language / languages: English as an attachment in your email.
The manual is 1,29 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
