817353
294
Zoom out
Zoom in
Previous page
1/377
Next page
292
Miscellaneous situations
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Jump lead terminal connections
The jump leads should only be connected in
the order 1 > 2 > 3 > 4 ›››Fig.196.
Switch o the ignition of both vehicles
››› .
Connect one end of the red jump lead to
the positive + terminal of the vehicle with
the flat battery A.
Connect the other end of the red jump lead
to the positive terminal + in the vehicle
providing assistance B.
Vehicles without a Start-Stop system:
connect one end of the black jump lead
to the negative terminal of the vehicle
providing the current B ›››Fig.195.
Vehicles with a Start-stop system: connect
one end of the black jump lead X to a
suitable ground terminal, to a solid piece of
metal in the engine block, or to the engine
block itself ›››Fig.196.
Connect the other end of the black jump
lead X to a solid metal component bolted
to the engine block or to the engine block
itself of the vehicle with the flat battery. Do
not connect it to a point near the battery A.
Position the leads in such a way that they
cannot come into contact with any rotating
part in the engine compartment.
Starting
Start the engine of the vehicle supplying
the current and leave it running at idle.
Start the engine of the vehicle with a dis-
charged battery and wait 2 to 3 minutes
until the engine runs.
Disconnecting the jump leads
Before disconnecting the jump leads,
switch o the dipped beam headlight if it
is on.
Turn on the heating fan and the vehicle's
heated rear window when the battery is
discharged to reduce the voltage peaks
that occur while disconnecting the battery.
While the engines are still running, discon-
nect the cables in the reverse order in
which they were connected.
If the engine does not start after 10 seconds,
wait for approximately 1 minute and then try
again.
WARNING
Please note the safety warnings refer-
ring to working in the engine compartment
›››page303.
The battery supplying the current must
have the same voltage (12V) as the flat bat-
tery. Failure to comply could result in an ex-
plosion.
Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even
once thawed, electrolyte leaks can cause
burns. Replace the battery if it is frozen.
Keep any sources of ignition (flames, ciga-
rettes, etc.) far enough away from the batter-
ies. They may cause an explosion.
Observe the usage instructions of the jump
lead manufacturer.
On the other vehicle, do not connect the
negative cable directly to the negative ter-
minal of the discharged battery. Any sparks
could ignite the igniter gas coming out of the
battery and could cause an explosion.
The negative wire must never be connec-
ted to fuel system components or brake lines
on the other vehicle.
Do not touch uninsulated parts of the pole
clamps. The jump lead attached to the pos-
itive battery terminal must not touch metal
parts of the vehicle, this can cause a short
circuit.
Jump leads must be placed in such a way
that they cannot be caught by rotating parts
in the engine compartment.
Do not rest your body on the batteries, as
this could cause burns.
Take into account the instruction manual of
the jump lead manufacturer and the instruc-
tion manual of the other vehicle.
294


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Seat Ateca 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Seat Ateca 2024 in the language / languages: English as an attachment in your email.

The manual is 19.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Seat Ateca 2024

Seat Ateca 2024 User Manual - German - 401 pages

Seat Ateca 2024 User Manual - Dutch - 400 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info