468758

Seagate BlackArmor Back-up Manual

125
Zoom out
Zoom in
Previous page
1/130
Next page
Copyright (c) 2000-2009 Acronis. All rights reserved.
Copyright (c) 2009 Seagate Technology LLC. All Rights Reserved. 125
It is also possible that the device is out of order, or the hard disk is not formatted.
B.3 Installing a SATA hard drive
Most recently manufactured PCs use the SATA interface for hard drives. In general,
installing a SATA hard drive is easier than an IDE drive, as it is not necessary to
configure master-slave jumpers. SATA drives use a thin interface cable with seven-
pin keyed connectors. This improves airflow through the PC case. Power is supplied
to SATA drives through 15-pin connectors. Some SATA drives also support legacy
four-pin power connectors (Molex) — you can use a Molex or SATA connector but
do not use both at the same time, because this could damage the hard drive. You'll
also need a free power lead fitted with a SATA power connector. Most systems that
come with SATA ports have at least one SATA power connector. If this is not the
case, you will need a Molex-to-SATA adapter. In case your system has the SATA
power connector but it is already occupied, use a Y-adapter that splits a lead in two.
B.3.1 Steps for installing a new internal SATA drive.
1. Find an unused SATA port using the documentation provided with your PC. If you
are going to connect your new SATA drive to a SATA controller card, install the
card. If you are going to connect the SATA drive to the motherboard, enable
applicable motherboard jumpers, if any. Most hard drive kits include a SATA
interface cable and mounting screws. Attach one end of the SATA interface cable to
a SATA port on the motherboard or interface card, and the other to the drive.
2. Then plug the power-supply lead or use a Molex-to-SATA adapter.
3. Prepare your drive. If you're installing a SATA 300 hard drive, check your PC's (or
SATA host adapter's) documentation to make sure it supports SATA 300 drives. If it
doesn't, you might need to change a jumper setting on the drive (see the drive's
manual for instructions). If you have a SATA 150 hard drive, you don’t need to
change any settings.
4. Turn on the PC and look for the new drive in the boot-up messages. If you don't
see it, enter the PC's CMOS setup program and search the BIOS configuration menu
for an option that will let you enable SATA for the ports you are using (or maybe
you will just need to enable SATA). See your motherboard documentation for
instructions specific to your BIOS.
5. If the operating system does not recognize the SATA drive, you need the
appropriate drivers for your SATA controller. If the drive is recognized, go to step 8.
Usually, it is best to obtain the latest driver version from the motherboard or
SATA controller manufacturer's website.
If you download a copy of the SATA controller drivers, place the driver files to a
known location on your hard drive.
6. Boot from the old hard drive.
The operating system should detect the SATA controller and install the
appropriate software. You might need to provide the path to the driver files.
7. Ensure that the SATA controller and the connected SATA hard drive are correctly
detected by the operating system. To do this, go to the Device Manager.
… 125 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Seagate BlackArmor Back-up at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Seagate BlackArmor Back-up in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info