664144
28
Zoom out
Zoom in
Previous page
1/80
Next page
ENGLISHENGLISH
55 |
TREKKING AND TREKKING-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2017ORIGINAL OPERATING INSTRUCTIONS 2017 | TREKKING AND TREKKING-PEDELEC
| 54
NOTE!
I
In case of inquiries, contact your SCOTT dealer or follow the respective in-
structions in the manual of the suspension fork manufacturer on this SCOTT
info CD.
NOTE!
I
If you have found the desired setting, write down the ideal inflation pressure
for later checks.
Adjusting the damping control
The damping is adjusted by valves inside. When the oil is forced through these
valves this slows down the speed with which the suspension fork is extended or
compressed and prevents the suspension “bouncing” after hitting an obstacle.
In this way it is possible to optimise the bicycle’s reaction to obstacles.
Suspension forks with adjustable rebound damping have an adjusting knob
(mostly red) (d) to slow down or accelerate the rebound movement. If a second
(mostly blue) knob is available, the compression speed can be set and/or the
lockout function can be activated.
Start the adjusting with a completely open damping (rebound movement at “-“).
Take hold of the handlebars with both hands and pull the front brake. Lean with
your entire weight on the fork and remove your weight immediately (e). The
fork will extract at the same speed as you made it compress.
Turn the red adjusting knob in the direction ”+ (f) until you hear a click. Com-
press the fork once again with the front wheel brake pulled and then remove the
weight abruptly once again. You will note that the fork extends more slowly.
Repeat the compression and the release by continuously turning the rebound
damping. You will get a feeling for the working of the rebound damping.
In the case of most suspension forks with coil springs a preload can be applied
to the springs within tight limits by turning a knob at the top of the fork crown
(a). If that is not possible and the desired negative suspension travel (“sag)
cannot be set, the coil springs must be replaced by harder or softer models. The
replacement is a job for the SCOTT dealer.
When replacing any parts, be sure to only use parts that bear the appropriate
mark and, to be on the safe side, original spare parts. Your SCOTT dealer will be
pleased to help you.
Always make a test ride over roads with various surfaces after each change to
the settings (b).
Check afterwards the position of the rubber ring/cable tie. Its distance from the
wiper is the maximum suspension travel that you have used (c). If the rubber
o-ring/cable tie has moved a few millimetres only, your rear shock is too firm.
Reduce the air pressure of air sprung forks or the initial spring tension of coil
springs. If that brings no improvement, have the springs replaced.
If the rubber ring/cable tie has shifted over the entire length of the tube or if
the fork audibly bottoms out and hits the top repeatedly when riding on bad
roads, the setting of the springs is too soft. In the case of air-suspension forks
the pressure must be increased. In the case of steel coils, have them replaced by
your SCOTT dealer.
DANGER!
G
Suspension forks are designed in a way to absorb shocks. If the fork is too
rigid and jammed, the terrain-induced shocks pass directly into the frame
without any damping. The frame is normally not designed to withstand such
undamped stresses. If your suspension has a lockout mechanism, do not acti-
vate the lockout function when riding in rough terrain, but only when riding over
smooth terrain (roads) and on field tracks.
CAUTION!
A
The suspension fork should be set up and adjusted in a way that it does not
reach the end of its travel, i.e. bottom out, unless in extreme cases. A spring
rate which is too soft (air pressure is too low) can usually be heard or felt as a
“clunk” type noise. This noise is caused by the sudden complete compression of
the suspension fork as it reaches bottom out. If the suspension fork frequently
reaches bottom out, it will fail over time, and so will the frame.
b ca e fd
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Trekking - 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Trekking - 2017 in the language / languages: English as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Trekking - 2017

Scott Trekking - 2017 User Manual - German - 81 pages

Scott Trekking - 2017 User Manual - French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info