664145
24
Zoom out
Zoom in
Previous page
1/64
Next page
ENGLISHENGLISH
47 |
ROAD BIKE | OWNER’S MANUAL 2017OWNER’S MANUAL 2017 | ROAD BIKE
| 46
See your SCOTT dealer and ask him to examine the remaining thickness of the
rims when you are through your second set of brake pads at the latest. Your
SCOTT dealer has special measuring devices for determining the remaining
thickness of the rims.
Both brake arms must hit the rim simultaneously, when you actuate the brake
lever. They must keep off the tyre.
A correctly adjusted brake is only ensured if all of these checks have been made
successfully.
DANGER!
G
Brake cables that are damaged (d), e.g. frayed, should be replaced imme-
diately, as they can otherwise fail in a critical moment, possibly causing a
crash!
DANGER!
G
Adjusting the position of the brake pads relative to the rims requires a
considerable degree of skill. Replacing and adjusting the brake pads is a job
best left to your SCOTT dealer.
DANGER!
G
Have your rims regularly inspected and measured by your SCOTT dealer (e).
Synchronising and readjusting
With dual pivot brakes, turn the small (headless) screw located at the side or on
top of the calliper (f), until the left and right brake pad are at the same distance
from the rim.
Also check whether the bolt by which the brake is screwed to the frame is still
tightened to the proper torque, i.e. according to the torque value given in the
chapter “Recommended torque settings for your SCOTT bike”.
The position of the brake lever where the brake starts to act, also referred to as
pressure point, can be adjusted to the size of the hand as well as to individual
convenience by readjusting the brake cable. Make absolutely sure you cannot
pull the brake lever all the way to the handlebar grip.
RIM BRAKES
Racing and side-pull brakes
Operation and wear
Actuating the levers on the handlebars (a) and cables (b) causes a brake pad
to be pressed against a brake surface. The ensuing friction slows down the
wheel. If water, dirt or oil come into contact with one of the braking surfaces,
this changes the coefficient of friction and deceleration is reduced. This is why
brakes respond with a slight delay and less powerfully in wet weather.
In order to maintain their effectiveness, brakes need to be checked and read-
justed regularly.
The friction generated by braking causes wear to the brake pads as well as to
the rims. Frequent rides in the rain and dirt and over hilly terrain can accelerate
wear on both braking surfaces. Some rims are provided with wear indicators,
e.g. grooves or circular indentations. If the rim is worn down to the point where
the grooves or indentations are no longer visible, they need to be replaced.
Once the abrasion of the rim has reached a certain critical point, the rim may
break under the tyre pressure. This can make the wheel jam or the inner tube
burst, both of which can cause an accident. Risk of falling!
Functional check
Test the brakes in stationary by firmly pulling the brake levers towards the
handlebars. The brake pads of rim brakes must hit the rim evenly with their
entire surface without touching the tyre during braking, in open condition or in
between.
Check whether the brake pads are accurately aligned with the rims and still suf-
ficiently thick. You can judge the wear of the brake pads by the appearance of
grooves. If the pads are worn down to the bottom of the grooves (c), it is time to
replace them. Be sure to observe the appropriate instructions of the respective
manufacturer.
The brake levers must always remain clear of the handlebars. You should not
even be able to pull them all the way to the handlebars in the event of an emer-
gency stop. If this is the case, however, observe the following chapter “Synchro-
nising and readjusting”.
b ca e fd
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Road Bikes - 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Road Bikes - 2017 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Road Bikes - 2017

Scott Road Bikes - 2017 User Manual - German - 65 pages

Scott Road Bikes - 2017 User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info