664188
8
Zoom out
Zoom in
Previous page
1/13
Next page
14
PLASMA 5 | BIKE OWNER’S MANUAL 2015 BIKE OWNER’S MANUAL 2015 | PLASMA 5
15
ENGLISH
ENGLISH
SEATPOST
Saddle assembly:
IMPORTANT
before assembling the saddle, make sure the seatpost saddle rail clamps
(524/525) are compatible with your saddle rails!
Measure your saddle rails height and width (HxW). Ritchey WCS Carbon One-Bolt
Saddle Rail Clamp outer-pieces specifications should be compatible with your
saddle rails.
If the saddle rails dimensions you measured are different from the saddle clamps
specifications, purchase the required saddle rail clamps parts at your retailer’s, the
following dimensions are available: 7x7mm, 8x8.5mm or 7x9.6mm.
Set the right saddle tilt and position the saddle rails so that the saddle rail clamps
are in the middle of the usable rail clamping area. Tighten the M6 screw (527) to the
specified torque (T13) to assemble the saddle.
Use the seatpost adjustment barrel to adjust your BB-Saddle horizontal offset.
Once the right offset is set, tighten the two M5 barrel screws (521) to the specified
torque (T12), in some cases, you will need to remove the saddle to access the two M5
barrel screws.
Battery/Seatpost assembly:
IMPORTANT
for electronic shifting assemble the seatpost battery mount parts (530) together so
that their concave surfaces are facing.
Put the O-ring part (531) into the groove and put the rubber part (532) in between
the two battery mount parts (530) so that one of its shoulders sticks out of the parts.
Assemble the battery mount parts (530) with the seatpost (501) by pinching the
upper end of the battery mounts and so that their pins coincide with the seatpost
low end holes.
Release the battery mounts once the pins are in position and pull apart the battery
mounts parts to leave enough space for the battery (999) to be mounted.
Once the battery mounts ribs are positioned into the battery groove, release the
battery mounts and connect the battery to the battery wire sticking out of the frame
seat tube.
Seatpost assembly:
IMPORTANT
before assembling the seatpost into the frame, make sure the rear side of the
seatpost (side where head is longer) is at the rear end of the frame.
Push gently the seatpost into the frame.
IMPORTANT
For electronic shifting: make sure the battery does not get stuck into the frame,
once the desired seatpost height is achieved pre-assemble the seatpost wedge:
position the upper wedge part (505) over the mid wedge part (504) and the low
wedge threaded part (503) below the mid wedge part.
Position the M6 wedge screw (506) into the assembly head up and pre-tighten it
over 3 turns. Position the wedge assembly into the seat tube insert in front of the
seat tube, its concave face should correspond to the seatpost front surface. Tighten
the M6 screw to the specified torque (T11) while making sure the upper surface of the
wedge coincides with the upper surface of the top tube.
Seatpost Plasma 4/5 SCOTT part number: 239318
Seat Clamp Plasma 4/5 SCOTT part number: 239544
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott Plasma 5 - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott Plasma 5 - 2015 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott Plasma 5 - 2015

Scott Plasma 5 - 2015 User Manual - German - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info