MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2017ORIGINAL OPERATING INSTRUCTIONS 2017 | MOUNTAIN BIKE AND MOUNTAIN BIKE-PEDELEC
| 38
bcaefd
DANGER!
G
After wheel mounting test the brakes in stationary. You should reach the
pressure point of the brake before the brake lever reaches the handlebars.
In the case of hydraulic brakes pump them, if necessary, until you reach a pre-
cise pressure point.
DANGER!
G
Do not open the red screw to open or close the RWS system.
NOTE!
I
Before mounting or replacing a fork/wheel combination with thru-axle
system, be sure to read first the manuals of the respective fork or wheel
manufacturer on this SCOTT info CD. More information are provided at
www.dtswiss.com
THRU AXLES ON THE SCOTT BIKE
Thru axles (d-f) provide suspension forks and rear frames with a higher stiff-
ness. Whenever your SCOTT bike is exposed to high loads, it remains direction-
ally stable and the suspension elements work as usual.
There is a wide range of thru-axle systems available now. Some systems are
tightened with quick-releases. Other systems may require special tools for as-
sembly or disassembly.
Whatever system you use, make sure during the assembly that the thru axles,
the drop-outs and the hubs are clean. Clean the components with an absorbent
cloth, if necessary, by using water and a little detergent.
In case you do not succeed in adjusting and fixing the wheel, as described, con-
tact your SCOTT dealer.
DANGER!
G
Improperly mounted wheels may throw you off your bike or result in
serious accidents! Therefore, if you have the slightest doubt, contact your
SCOTT dealer and ask him to explain the system of your SCOTT bike to you.
Hold the lock nut on the right side of the hub tight. Turn the RWS quick-release
lever clockwise to pre-tighten the RWS system. Depending on the fork mounted
or the frame model, the number of turns you need varies. You need at least six,
in most cases however more turns. During the first turns you should be able to
turn the RWS quick-release lever nearly without resistance.
Turn the quick-release lever subsequently forcefully clockwise until the axle is
hand-tight.
Make sure the RWS quick-release lever does not stand out to the front (a). Open
the RWS quick-release lever a little (b, position 1) to bring it into a favourable
position. Turn the quick-release lever then into the desired position (b, posi-
tion2) and re-close it towards the hub (b, position 3).
Close the release lever of the brake or hook in the cable. Actuate the brake lever
to make the brake work. The brake pads of rim brakes must hit the rim evenly
with their entire surface without touching the tyre during braking, in open con-
dition or in between.
Lift the wheel and give it a strong tap from above. The wheel must be securely
fixed and must not rattle.
Wheel removal
To open the RWS system turn the quick-release lever anticlockwise (c) by hold-
ing the lock nut tight on the other side of the hub. Typically, you need not open
the RWS system completely. Open it only so far until the wheel slides off the
drop-outs. Open it fully only in exceptional cases and remove the axle com-
pletely from the hub.
DANGER!
G
Improperly mounted wheels may throw you off your bike or result in
serious accidents! Therefore, if you have the slightest doubt, contact your
SCOTT dealer and ask him to explain the system of your SCOTT bike to you.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Scott MTB Ebike 2017 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Scott MTB Ebike 2017 in the language / languages: English as an attachment in your email.
The manual is 4.7 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
