331265

Scholtes ttg 7324 Manual

15
Zoom out
Zoom in
Previous page
1/60
Next page
GB
15
UNDERSIDE OF HOB
L N
1 2 3 4 5
Blue
Brown
N
Neutral
L
Live
Green/Yellow
Earth
5
1
2
3
4
U-bolt
connection support
Phase Neutral Earth
The thickness of the supporting surface should be taken
into account when choosing screws for the fixing hooks:
30 mm thick: 17.55 mm screws
40 mm thick: 7.55 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided in the centre of each side
of the hob.
2. Insert the hob in the cavity, make sure it is in a central
position and push down on the whole perimeter until the
hob is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob into
its cavity, insert the 4 fixing hooks (each has its own pin)
into the lower edges of the hob, using the long pointed
screws to fix it in place, until the glass is stuck to the
supporting surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts that ensure the safe operation of the appliance
must not be removable without the aid of a tool.
Electrical connection
! The electrical connection of the hob and any built-in
oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Terminal board
On the lower part of the
appliance there is a connection
box for the different types of
electricity supply (the picture is
only an indication and is not an
exact representation of the
purchased model).
Single-phase connection
! The cable provided should only be used for this type of
installation.
Mains supply characteristics:
Voltage and mains frequency
 230/240V 1+N ~ 50 Hz
 230V 2 ~ 50 Hz
If the hob has a supply cable fitted,
connect it to the mains, using the
colours as a guide (see diagram).
If the hob does not have a supply cable fitted, proceed
as follows:
1. Use the supply cable provided (where applicable) or
a suitable supply cable, H05VV-F or higher, with the right
dimensions (cable section: 2.5 mm).
2. To open the terminal board, insert a screwdriver into
the side tabs of the cover (see Terminal board picture).
3. The terminal board is designed for single-phase
connection: make sure the connection supports between
springs 1 and 2 and those between 4 and 5 are in the
right position (see Single-phase picture).
4. Position the wires according to the following diagram
and table and connect the appliance by tightening all
the screws for the springs as much as possible.
Single-phase
5. Secure the power supply cable by fastening the
clamp screw then put the cover back on.
Voltage and
mains
frequency
Electrical connections
Terminal
board
230/240V 1+N ~
50 Hz
230V 2 ~ 50 Hz
Single-
phase
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scholtes ttg 7324 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes ttg 7324 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info