Manual Scholtes hp 95 (page 11 of 48) (English, German, Dutch, French, Italian, Spanish)

128412

Zoom out

Zoom in

1/48

Assembly Instructions for hp 97

The hood is intended for wall mounting (Fig 1A).

1. Remove the two screws "M" that fasten the

mobile part "B" of the duct to the fixed part "A"

(see fig. 1A);

2. Place the two angle irons "D" on the top of the

hood;

3. Remove the aluminium grease filters

4. Place the hood up against the wall and mark the

wall in correspondence with hooks "G" and "D";

5. Using a 6 mm diameter drill bit, drill the holes in

the wall where the positions were previously

marked.

6. Insert the expanding rawlplugs "1" into the holes

and pre-screw hooks "E"

7. Tighten the support screws "2" of angle irons "D"

half-way.

8. Now you can proceed with levelling the hood

(rigging) using screws "L". Once the appliance has

been levelled correctly, fasten it definitively to the

wall by tightening the support and fastening

screws of angle irons "D" as well as screws "F".

Put the metal grease filters back in place.

Assembly Operations for hp 95

This type of support is supplied with the hood (generally

in two pieces) and should be fastened to the wall by

means of two rawlplugs.

In this case, some slots have been made on the

back of the hood onto which these supports should

be hooked (see figure 2A).

To adjust the position of the hood, the support fixing

screws should be loosened and the height of the

same should be adjusted. The aforementioned 2

types of support are nevertheless not sufficient to

guarantee that the hood is firmly anchored; it could in

fact become dislodged and fall to the ground.

To avoid this danger, one solutions can be applied to

the hood:

· ANTI-TIPPING SCREW - This anti-tipping device

foresees that the hood is fastened directly to the

wall by means of one or more screws provided,

using the holes on the back panel of the hood

(see point "P" in figure 2A).

Installation

Assembly Operations

· locate the position of the holes to drill on the wall

for fastening screws and hooks: then remove the

grease filters, bring the hood close to the wall and

place it in the desired position; mark the exact

points on the wall where the holes must be drilled;

· remove the hood and follow the instructions given

above to anchor the same to the wall according to

the type of support;

· hook the hood on;

· now proceed with the anti-tipping fastening using

the special brackets or screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes hp 95 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scholtes hp 95 Manual

Product: